InVento Sportkites X-CELERATOR Mode D'emploi

X-CELERATOR
The radical Speed Kite was developed especially for »stormy times«. It
requires the highest attention levels, quick reactions and a strong hand.
Beginners should leave it alone. The X-CELERATOR develops soaring speed
with increasing wind. At 3 Bft., the dance can begin. Fast, yet still manageable,
it flies powerful and precisely. Between 4 and 5 Bft., the pilot can feel the kite's
strength. Very powerful and rapid, it now requires the highest level of concent-
ration. What follows is already very extreme.
X-CELERATOR: speed paired with fierce power and good precision.
Tips for Assembly
Use the enclosed brochure, "Advice on Flying Sport Kites" when building
the X-Celerator. Both battens offer a special feature for assembly that are not
included in the standard instructions. Assemble the battens as follows:
1. Tighten the keel by hooking the loop into the split cam.
2. You can trim the X CELERATOR using the knot guide on the upper leading
edge connector. The kite is faster if the lark's head is set toward knot D.
If you choose knot A, the kite will hold its stiffest setting. With this setting,
you will get more pull, but the kite will be more difficult to start and fly. It
does increase the tendency to overturn.
In general, move the knots toward A for high wind and toward D for lighter
wind.
3. Insert the longer poles into the inside pockets (yellow) and the shorter
poles into the outside pockets (green).
4. Insert the other ends into the connectors on the bottom spreader.
5. Check the spacing of the connectors based on the dimensions shown in
Figure 5.
Tips for Starting
Because the optimized sail is flat for speed, it takes practice to start the
X-CELERATOR – particularly if you want to start the kite without a second
person for assistance.
It is easiest to lay the fly lines out completely, place the hand loop over a
ground anchor (tent peg or ground stake) and put some tension on the kite
lines so that it cannot start up on its own. In addition, tip the kite with the
flight tip toward the hand loop so that the nose tips back somewhat.
1 2
A
6mm Carbon
540mm
Specification · Technische Daten · Spécifications techniques · Datos técnicos
X-CELERATOR
Wingspan · Spannweite · Envergure · Alcance:
Heigh · Höhe · Hauteur · Altura:
Rec. line · empf. Schnur · Lignes conseillées · Cuerda suj.:
Wind range · Windbereich · Plage de vent · Viento:
Sail fabric · Segelmaterial · Voilure · Vela:
The right to make technical alterations is reserved!
Technische Änderungen vorbehalten!
Tous droits de modifications techniques réservés
Se reserva el derecho a realizar modificaciones técnicas.
D
C
B
6mm Carbon
340mm
6mm Carbon
1000mm
GFK 2mm
245mm
GFK 2mm
225mm
6mm Carbon
570mm
2x30 m | 100 kp
12-49 km/h | 8-31 mph
Ripstop-Nylon
5
~16cm
~3cm
3
X-CELERATOR
Product Information
Produktinformation
Mode d'emploi
Informació de Producto
158 cm
68 cm
4
celerator
designed by: Michael Tiedtke
Art.-No. : 117010
INVENTO GmbH
Klein Feldhus 1
D - 26180 Rastede-Neusüdende
Germany
Service: +49 (4402) 92 62 44
Email: service@invento-hq.com
www.invento-hq.com
US Distribution by:
HQ Kites & Design U.S.A., INC
317 Great Bridge Blvd., Suite C
Chesapeake, VA 23320, USA
Toll free: (888) 318 - 3600
Email: sales@hq-kites-usa.com
www.hq-kites-usa.com