Eaton PKZM0-EA Serie Instructions De Montage

Инструкция по монтажу
Návod k montáži
05/18 IL034045ZU
Instrukcja montażu
Instrucţiuni de montaj
Montaj kılavuzu
PKZM0-...-EA
PKZM01-...-EA
a
PKZM0-...C-EA 10 mm (0.39") ①
②
PKZM0(1)-...-EA 10 mm (0.39")
U(A)-PKZ0... 9 mm (0.35")
AGM2... 9 mm (0.35")
NHI...-PKZ0 9 mm (0.35")
NHI-E...PKZ0 6 mm (0.24")
L
②
I >
T
for Canada:
PKZM0 with AK-PKZ0,
for use as self protected
combination motor controller!
Emergency On Call Sevice:
Local representativ (Eaton.eu/aftersales) or +49 (0) 180 5 22 38 22 (de, en)
⌀ 3 - 6.35 mm ⌀ 6.35 mm
...A (⌀ 0.12 - 0.25") (⌀ 0.25")
Eaton Industries GmbH, Hein-Moeller-Straße 7-11, 53115 Bonn, Germany
© 2017 by Eaton Industries GmbH, Eaton.eu/documentation
05/18 IL034045ZU
Eaton.com/recycling All Rights Reserved Printed in Austria (05/18)
CAUTION
Manufacturer's instructions for
selecting overload and short-circuit
①
≧ 15 mm
protection must be followed. If an
(≧ 0.59")
①
overload or fault current interruption
②
≧ 55 mm
has occurred, current-carrying
(≧ 2.17")
components or the controller should
be examined and replaced if damaged.
①
AVERTISSEMENT
Il est impératif de respecter les
instructions du fabricant en
choisissant les dispositifs de
protection contre les surcharges
et les court-circuits. En cas de
coupure due à une surcharge ou à
pour Canada:
un courant de défaut, examiner les
PKZM0 avec AK-PKZ0,
éléments porteurs de courant et le
peut étre employé comme
contrôleur et les remplacer s'ils
contrôleur de combinaison
a moteur auto-protégé.
sont endommagés.
OFF
U(A)-PKZ0...
PKZM0-...C-EA
1 x (0.75 - 2.5 mm
1.7 Nm
2
0.75 - 2.5 mm
2 x (0.75 - 2.5 mm
(15.1 lb-in)
2
0.75 - 2.5 mm
1 x (0.75 - 2.5 mm
DIN46228
2 x (0.75 - 2.5 mm
UL AWG18 - 14 1.8 Nm
AGM2-...-PKZ0, NHI...-PKZ0
Cu 75 °C WIRE
(16 lb-in)
PKZM0(1)-...-EA
1.7 Nm
2
1 - 6 mm
(15.1 lb-in)
2
1 - 4 mm
NHI-E...-PKZ0
2
1 - 6 mm
DIN46228
1.8 Nm
UL AWG18 - 8
Cu 75 °C WIRE (16 lb-in)
AGM2-...-PKZ0
U-PKZ0
A-PKZ0
PKM0-...-EA
NHI...-PKZ0
PKZM01-...-EA
NHI-E-PKZ0
2
)
1.2 Nm
2
)
(10.6 lb-in)
2
)
AWG18 - 16
2
)
2
1 x (0.75 - 1.5 mm )
1 Nm
2
2 x (0.75 - 1.5 mm )
(8.85 lb-in)
2
1 x (0.75 - 1.5 mm )
AWG18 - 14
2
2 x (0.75 - 1.5 mm )
2
1 x (0.75 - 1.5 mm )
1.2 Nm
2
2 x (0.75 - 1.5 mm )
(10.6 lb-in)
2
1 x (0.75 - 1.5 mm )
AWG18 - 16
2
2 x (0.75 - 1.5 mm )
a = 10 mm
(a = 0.4")
2
1
3
0.6 x 3.5
≦ 2.5 mm 2
(≦ AWG 14)