Publicité
EN
ENgLISH
make sure that the ECono-hEAt eCare heated mattress pad is the correct size for your mattress. do not use an over sized electric
1
mattress pad and tuck it in.
place the electric mattress pad directly on the mattress with the label at the top end of the bed facing upward.
2
Starting at the foot end of the bed fit the electric mattress pad to the mattress with the elastic bands provided. Then secure the top
3
end. At the top end there might be a small overlap of the electric mattress pad, depending on the length of the mattress. The flexible
elastic bands will ensure that the electric mattress pad fits all mattresses. Ensure that electric mattress pad is flat on the mattress
with no folds or creases.
Carefully fit the bottom sheet over the electric mattress pad, ensuring that the electric mattress pad remains flat.
4
OpERATINg yOuR MATTRESS pAD
Ensure that the flexible lead from the control switch is firmly plugged into the socket of the electric mattress pad.
1
plug the AC/dC adaptor (part no. ZBhWX-A2100276-A ) into the wall socket and switch on. A green lEd light on the adaptor will
2
indicate that the adaptor is working.
move the slider switch on the controller to the desired heat setting recommended for continuous use: position i – low (±75°f)
3
or position ii – medium (±85°f). the red lEd light will indicate that the mattress pad is on. position iii (Boost, ±95°f) is not
recommended for continuous use.
pUShBUtton boost settings (see pictorial diagram
4
a) SinGlE tAp
BooSt modE (20 minute preheat timer): to preheat the electric mattress pad, set the control slide switch to the
desired setting recommended for continuous use – position i or ii and press the
will indicate that the electric mattress pad is in boost mode. After 20 minutes the green lEd light will turn off and the control
switch will automatically revert to the pre selected heat setting.
b) doUBlE tAp
BooSt modE (1 hour auto off timer): to activate the 20 minute boost and 1 hour auto off timer, preset
the control slide switch to the desired setting recommended for continuous use – position i or position ii and press the
pUShBUtton tWiCE. The flashing green LED light will flash indicating that the electric mattress pad will preheat (boost)
for 20 minutes and then automatically switch to the pre selected heat setting. the electric mattress pad will remain on for a
further 40 minutes and then automatically switch off. to switch the electric mattress pad on again move the control slide
switch to position o - off and back to the desired heat setting recommended for continuous use:
position i – low or position ii – medium.
AUtomAtiC EnERGy SAVER 10 hoUR SWitCh off: the control switch is designed to automatically switch off after 10 hours
5
of continuous use. if the electric mattress pad is still required move the control slide switch to position o – off and back to the
desired heat setting recommended for continuous use: position i – low or position ii – medium.
Unplug the AC/dC adaptor from the wall socket when not in use.
6
a
Wall plug
B
power Supply
doUBlE*, QUEEn & KinG SiZE BEdS
fEATuRES
1. Safety Extra low Voltage (SElV Class iii)
– the Ultimate in health and Safety
2.
Extra safe and shockproof
3.
Eliminates harmful electromagnetic radiation associated
with other electric mattress pads
4.
machine washable and dryable
5.
Soft, luxurious and comfortable
6.
outer covering made from 100% cotton
7.
three heat settings – low, medium and high with two
convenient off positions
8.
Convenient boost timer heats up your bed faster, for those
extra cold nights
9.
low setting is extra low which provides a desirable setting
for comfortable all-night sleep
HEALTH AND SAfETy
the ECono-hEAt eCare heated mattress pad uses only 21 V dC and emits minimal electromagnetic waves, making it a safe and
healthier choice compared to other electric mattress pads.the mattress pad is machine washable and is made of 100% cotton exterior
so that you can sleep undisturbed all night long.
wASHINg INSTRucTIONS
Important, before washing detach hand controller(s) from the electric mattress pad and
secure connector flaps to mattress pad using snap fasterners.
minutes in lukewarm water and mild soap. do not scrub. Rinse well.
mattress pad in washing machine. Wash using gentle cycle (85°f). Spin dry.
dry for 10 minutes on low setting. then drape over washing line until completely dry.
do not wet the electric control switch.
do not dry clean.
do not wash the mattress pad if any wires have worn through the fabric.
do not use bleach.
All manuals and user guides at all-guides.com
fITTINg yOuR HEATED MATTRESS pAD
C
Control Switch
below):
D
Removable Controller
SinGlE & doUBlE* SiZE BEdS
10. Energy saving – turns off automatically after 10 hours if left
on accidentally
11. Energy saving – only uses a maximum of 60W on high
setting
12. Convenient user-selectable one hour timer – automatically
switches off after falling asleep
13. the mattress pad creates a comfortable warm feeling, which
is close to the body's natural temperature
14. Available in Single, double, Queen and King size
15. Easy to fit – adaptable elastic straps fit all mattress heights
and lengths
16. international safety standards approved
17. two year warranty
do not iron.
do not reconnect the mattress pad until it is completely dry.
do not wring.
pUShBUtton onCE. the green lEd light
GREEn lEd
REd lEd
off
hiGh
mEdiUm
loW
off
*the double mattress pad
(137 x 200cm) is available with single
or dual controllers.
hAnd WAShinG:
mAChinE WASh:
dRyinG:
pUSh BUtton
press once = Boost
(20min preheat timer)
press twice = Boost
(1hr auto off timer)
REd SlidER
(heat selection)
Soak for 15
place
tumble
Publicité
