FORM FIT HD 21D 06 Instructions De Montage

FORM FIT HOOD PROTECTOR
Volkswagen Passat 2006 -
Thank you for purchasing a form fit hood protector.
Care Instructions
Clean the protector with a mild soap and water solution or plastic cleaner only.
Periodically check to make sure all the hardware is in place and the protector is secure.
Attention!
Do not use chemicals or solvents. Avoid using automatic car washes. Do not pull on the
protector when opening or closing the hood.
Hardware Kit
x 3 x 4 x 4
Tools Required
Installation Instruction
Be sure that the hood is clean and dry inside and out. Release the hood of the vehicle, but do not open it.
1.
2. Install the bumpons as shown in Illustration #1A. Attention: The bumpons must be installed on the
hood not the protector!!!! If the bumpons are installed on the protector, they will wear through the paint.
Center the protector on the hood, resting on the bumpons.
3.
4. Peel and fold an anti-abrasion film pad in half over the edge of the hood, underneath each of the two (2)
inner holes in the protector. See Illustrations #1B & #2 - Step 4.
5a) Place a clip over each of the anti-abrasion film pads on the edge of the hood as shown below in
Illustration #2 – Step 5a.
b) Insert a pin through the protector into each of the clips. See Illustration #2 – Step 5b.
c) Insert a #6 x 5/8'' screw through an 'L'- bracket and into the clip. See Illustration #2 – Step 5c & 5d.
d) Make sure all the components are well seated together; the protector is centered on the hood, and then
tighten the screws into the clips.
6. Repeat step #4 and #5 for the other two (2) holes.
7. On some vehicles it may be necessary to adjust the hood bumpers and/or latch for proper clearance.
Note: Do not pull on the protector when opening or closing the hood.
Illustration # 1: Bumpon Location and Clip Placement
10" 10"
A
1"
4" 4"
Illustration # 2: Clip Configuration – Patent No. 6,892,427
Step #4
Step #5a
Made in Canada
All manuals and user guides at all-guides.com
HD 21D 06
'L'
# 6 x 5/8''
Bracket
Screws
x 4 x 4 x 4
#
2
B
Clips
(Step #4 & #5)
Clips (Step #6)
Step #5c & 5d
Step #5b
Rev1.100129
FORM FIT HOOD PROTECTOR
Volkswagen Passat 2006 -
Thank you for purchasing a form fit hood protector.
Care Instructions
Clean the protector with a mild soap and water solution or plastic cleaner only.
Periodically check to make sure all the hardware is in place and the protector is secure.
Attention!
Do not use chemicals or solvents. Avoid using automatic car washes. Do not pull on the
protector when opening or closing the hood.
Hardware Kit
x 3 x 4 x 4
Tools Required
Installation Instruction
1. Be sure that the hood is clean and dry inside and out. Release the hood of the vehicle, but do not open it.
2. Install the bumpons as shown in Illustration #1A. Attention: The bumpons must be installed on the
hood not the protector!!!! If the bumpons are installed on the protector, they will wear through the paint.
3. Center the protector on the hood, resting on the bumpons.
4. Peel and fold an anti-abrasion film pad in half over the edge of the hood, underneath each of the two (2)
inner holes in the protector. See Illustrations #1B & #2 - Step 4.
5a) Place a clip over each of the anti-abrasion film pads on the edge of the hood as shown below in
Illustration #2 – Step 5a.
b) Insert a pin through the protector into each of the clips. See Illustration #2 – Step 5b.
c) Insert a #6 x 5/8'' screw through an 'L'- bracket and into the clip. See Illustration #2 – Step 5c & 5d.
d) Make sure all the components are well seated together; the protector is centered on the hood, and then
tighten the screws into the clips.
6. Repeat step #4 and #5 for the other two (2) holes.
7. On some vehicles it may be necessary to adjust the hood bumpers and/or latch for proper clearance.
Note: Do not pull on the protector when opening or closing the hood.
Illustration # 1: Bumpon Location and Clip Placement
10" 10"
A
1"
4" 4"
Illustration # 2: Clip Configuration – Patent No. 6,892,427
Step #4 Step #5a
Made in Canada
HD 21D 06
'L'
# 6 x 5/8''
Bracket
Screws
x 4 x 4 x 4
#
2
B
Clips
(Step #4 & #5)
Clips (Step #6)
Step #5c & 5d
Step #5b
Rev1.100129