JO-EL 821027 Mode D'emploi page 7

All manuals and user guides at all-guides.com
gb usER's guidE
Please read this guide carefully before switching on and using this product.
Safety instructions
1. The fan heater must be connected to an earthed power
source.
2. The fan heater must be placed on a flat, horizontal sur-
face. It must not be inverted.
3. Please be aware that the fan heater becomes very hot
when in use and therefore must be placed away from
combustible material, and not placed on a combustible
surface.
4. The fan heater must not be covered due to the danger of
fire.
5. The fan heater must not be placed under a power
socket.
6. The fan heater must not be exposed to moisture or wa-
ter. It must not be used outdoors in rainy weather.
7. The fan heater must not be connected to a timer or any
similar product.
Use of the fan heater
1.
1. Connect the fan heater to the power outlet.
2. Turn the function selector (Fig. 1 - u) to the desired position.
3. The thermostat knob (Fig. 1 - v) is set for temperature selection (stepless).
• When the fan heater's internal thermostat (overheating protection) reaches its maximum temperature, it automatically
turns off the heating element – (the fan continues running on the 9 and 15 kW models). Once the temperature is normalised,
the heating element is activated again. The temperature is regulated within several degrees and a little click is heard when
the relay turns on and off.
Safety thermostat (only for the 9 kW and 15 kW models)
If the thermal cutout is activated (at temperatures above 110 ºC), the safety thermostat must be reconnected. You can do this
only after the temperature in the fan heater has fallen. Unscrew the cover (Fig. 2) and press gently the reset button with your
finger. Connection is re-established and the fan heater can function again after cooling.
After use
2kW, 3.0kW and 5kW: Set the function selector (Fig. 1 - u) to ventilation without heating (+) for 3 minutes. The fan heater can
then be turned off. Do not turn off the fan heater from the power outlet or by pulling the power cord from the outlet.
9kW and 15kW: Set the function selector (Fig. 1 - v ) to 0 and wait until the fan stops automatically. Do not turn off the fan
heater from the power outlet or by pulling the power cord from the outlet.
Specifications
item No.
Power (kW)
Max. grid current (A)
Circulated air quantity
(m3/hour)
Power supply
Plug system
Cord length (m)
Disposal
The product must not be disposed of together with ordinary household waste. Follow the local guidelines on the disposal of
unwanted electrical appliances (available at www.jo-el.com/weee).
Plug the fan heater into the power socket.
= the fan heater starts
= the fan runs + partial heating
= the fan runs + full heating
821034 821035
1 / 2 1 / 2 / 3
8,7 13,0
170 330
230-240V AC 50-60 Hz
Schuko
1,2
8. The fan heater must not be kept in a room which con-
tains combustible liquids or gases.
9. If the fan heater is connected by means of an extension
cord, this must be as short as possible and should al-
ways remain fully uncoiled (because of the risk of de-
veloping a heat build-up).
10. No other appliance must be connected to the same
socket as the fan heater.
11. Do not use the fan heater close to bath tubs, showers or
swimming pools.
12. The fan heater must not be permanently fixed.
13. Do not use the fan heater if the socket or plug has been
damaged. Only an authorized electrician or an authori-
zed workshop is allowed to replace plugs or similar. If you
are in doubt, please contact your supplier.
821027 821028
2,5 / 5 4,5 / 9
7,2 13,5
340 820
400V
CEE17 16A
1,6
821029
7,5 / 15
21,6
1600
CEE17 32A