Euromate 477573 Mode D'emploi page 16

All manuals and user guides at all-guides.com
Standventilator_477573.book Seite 16 Dienstag, 15. November 2016 3:33 15
GB
• Disconnect the power supply before transport-
ing the device.
Device-specific safety instructions
• The product must be standing on an even, hori-
zontal surface with clearance to all sides.
• The product may not be operated outdoors.
• Never put objects through the protective grille
into the product.
• Objects that can be pulled (e. g. curtains, plants),
must not be in the immediate vicinity.
• Never expose the product to water or other liq-
uids.
• The product must not be operated in rooms with
bathtubs, showers or swimming pools or near to
wash basins or water connections.
• Remember that moving parts may also be
located behind ventilation and venting slots.
• Symbols appearing on your device may not be
removed or covered. Signs on the device that
are no longer legible must be replaced immedi-
ately.
Read and observe the instructions for use
before using the product for the first time.
Your product at a glance
► P. 2, item 1
1. Front Grille
2. Blade Cap
3. Blade
4. Plastic Mounting Nut
5. Rear Grille
6. Motor Shaft
7. Oscillating Knob
8. Motor Housing
9. Neck Screw
10. Switch Box
11. Set Screw
12. Inner Tube
13. Height Adjustment Collar
14. Outer Tube
15. Base Decorative Cap
16. Screw
17. Cross bar A
18. Cross bar B
19. Screw
20. Decorative cover
Assembly
► P. 2, item 1
Assemble of base
– Firstly, loosen and remove the four screws from
the bars. Then cross bar A and bar B so that they
interlock.
– Be sure to align the four holes in the bars with
those on the flange of the Outer Tube. Secure
the flange to the bars with the four screws.
16
– Loosen and remove the Height Adjustment Col-
lar from the top of the Inner Tube. Slide the Base
Decorative Cap down over the assembly.
– Replace the Height Adjustment Collar on top of
the Inner Tube. Pull the Inner Tube out from the
Outer Tube to adjust the tube to the desired
height and tighten the collar.
– If necessary, slightly loosen the Set Screw by
turning it anticlockwise. Slide the Switch Box
down over the Inner Tube and tighten the Set
Screw. Make sure the Set Screw is tightly
secured.
Assemble of blade and grille
– Before assemble the grille, should place the dec-
orative cover on front grille first then fix by indi-
cated screws.
– Unscrew the plastic mounting nut from the front
of the motor housing by rotating it anticlockwise.
– Position the rear grille against the front of the
motor housing with the handle uppermost, ensu-
ing that the locating pegs on the motor housing
are engaged correctly in the holes of the rear
grille.
– Tighten the Rear Grille Mounting Nut clockwise.
DO NOT OVERTIGHTEN IT.
– Push the fan blade onto the motor shaft, locating
the slot at the back of the blade on the drive pin
that passes through the motor shaft.
– Tighten the blade cap by turning it anticlockwise.
– Position the front grille against the rear grille so
that the holes in the rims that accept the small
nut and bolt are in line. Insert the bolt through the
holes and screw on the nut. Do not fully tighten
at the stage.
– Push the grille retaining clips into position ensur-
ing that they engage correctly on the rim of the
grille.
– Fully tighten the small nut and bolt that passes
through the rim of the grille.
Operation
Check before switching on!
DANGER! Caution, risk of injury! The
product may only be put into operation if no
faults are found during the check-up.
Ensure that any defective parts are
replaced before the product is used again.
Check the safe condition of the product:
– Check whether there are any visible defects.
– Check whether all parts of the product are firmly
attached.
Operation of the product
– Place your fan on a level and dry surface.
– Plug the fan in to a mains socket. Select the
desired speed setting. There are 4 settings – 0
(off), 1 (low), 2 (medium) and 3 (high).
– The fan can be set to oscillate by pushing Oscil-
lating Knob downwards. To stop the oscillating
feature, pull-up the Oscillation Knob.
– To adjust the tilt angle of fan head, loosen the
neck screw, swivel the fan to the desired angle
and then re-tighten the screw.