Publicité
Liens rapides
Model/Modelo/Modèle
B2510LF / B2510LF-PPU
B2512LF / B2512LF-PPU
B2511LF-PPU / B2515LF-PPU
Series/Series/Seria
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:
For easy installation of your Delta faucet
you will need:
・To READ ALL the instructions completely before
beginning.
・To READ ALL warnings, care and maintenance
information.
・To purchase the correct water supply hook-up.
Para instalación fácil de su llave Delta
usted necesitará:
・LEER TODAS las instrucciones completamente
antes de empezar.
・LEER TODAS los avisos, cuidados, e información
de mantenimiento.
・Comprar las conexiones correctas para el
suministro de agua.
Pour installer votre robinet Delta
facilement, vous devez:
・LIRE TOUTES les instructions avant de débuter.
・LIRE TOUE LES les avertissements ainsi que toutes
・Acheter le bon nécessaire de raccordement.
www.deltafaucet.com
86600
B2510LF
B2511LF-PPU
B2510LF-PPU
86600
1
TWO HANDLE WASHERLESS
LAVATORY FAUCET
LLAVE DE LAVAMANOS
DE DOS MANIJAS SIN ARANDELAS
ROBINET SANS RONDELLE À
DEUX MANETTES POUR LAVABO
B2512LF
B2512LF-PPU
3/32" (2.38mm)
B2515LF-PPU
?
6/24/2015 Rev. B
Publicité
Manuels Connexes pour Delta B2510LF
Sommaire des Matières pour Delta B2510LF
- Page 1 B2510LF-PPU B2512LF-PPU You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin: 3/32" (2.38mm) For easy installation of your Delta faucet you will need: ・To READ ALL the instructions completely before beginning. ・To READ ALL warnings, care and maintenance information.
- Page 2 SHUT OFF WATER SUPPLIES. Secure faucet to sink using locknuts provided (1). Continue to either step 3 metal pop-up installation or step 4 plastic pop-up installation. If your model does not have a pop-up skip to step 5. Remove old faucet. Place gasket (1) on bottom of new faucet. Place faucet through mounting holes in sink.
- Page 3 Metal Pop-Up installation Push washer (4) and gasket (5) down. Remove tailpiece (6) from body (7), add Plumber tape (8), replace tailpiece. nut, washer & gasket (4), clean off excess silicone. Remove pivot nut (1). Install horizontal rod (2) and stopper (3) as Attach horizontal rod (1) to strap (2) using clip (3).
- Page 4 Install Pop-Up Assembly Screw flange onto body. Pivot hole (3) must face back of sink. black gasket (4) down. Tighten nut/gasket, clean excess silicone. Remove pivot nut (1). Install horizontal rod (2) and stopper (3) as Insert lift rod (1) through faucet and into strap (2). Tighten screw (3). removable (4) or non-removable (5).
- Page 5 CONNECT TO WATER SUPPLIES. FLUSH SYSTEM/CHECK FOR LEAKS. (HOOK-UPS NOT PROVIDED). Remove aerator (1) and turn faucet handles (2) all the way on. Turn on Determine which type of connection you will be making. Important: This ushes away any debris that could cause damage to internal parts.
- Page 6 Maintenance If faucet e hibits very low ow: A. Remove and clean Aerator (3) (page 3), or SHUT OFFWATER SUPPLIES B. Clean Seats and Springs (2) of any debris. If faucet leaks from spout: *Install stems (1) correctly for proper handle rotation: Note: The stops (4) must point to the center of the faucet for proper handle Replace Stem Unit Assembly (1) and Seats and Springs (2).
- Page 7 RP74151 RP70851 Hot & Cold Lever Hot & Cold Lever Handles w/Screws Handles w/Screws Manijas en palanca con tornillos de agua fría y caliente Manijas en palanca con tornillos de agua fría y caliente RP41680 Hot & Cold Lever Handles w/Screws Manijas en palanca con tornillos de agua fría y caliente RP20547 Retention Screws...
- Page 8 été enregistré auprès de Delta Aucune garantie ne couvre les piles.