Siemens TS25 Serie Notice D'utilisation page 13

Automatic clean warning
(depending on model)
Pilot light (3) will flash indicating that boiler must be rinsed.
To do this, follow the procedure described in the section
above.
To reset "Calc'n clean" pilot light and counter, switch the
station off twice, keeping it off during at least 30 seconds
each time
Rinsing the iron steam chamber (G)
Caution! Risk of burns!
This procedure helps to remove scale particles out of the
f
steam chamber.
Carry it out approximately every 2 weeks, if the water in
f
your area is very hard.
a) Ensure that the iron is cooled down.
b) Set the temperature selector (10) of the iron to the "min"
position.
c) Fill the tank with tap water.
Trouble shooting
Problem
The steam generator
does not come on.
The iron does not
r
heat up.
The iron begins
r
to smoke when
switched on.
Water flows through
the holes on the sole
plate.
Dirt comes out
through the sole
plate.
r
The iron does not
produce any steam.
Possible causes
• There is a connection problem.
• The main power button is not switched on.
• The main power button is not switched on.
• The temperature control knob is set to the
"min" position.
• During first use: Certain components on
the appliance have been lightly greased at
the factory and may produce a little smoke
when initially heated.
• During later use: the soleplate may be
soiled.
• The steam function is being used before it
has reached temperature.
• The water is condensing inside the pipes
because steam is being used for the first
time or has not been used for a long time.
• There is a build-up of scale or minerals in
the steam tank.
• Chemical products or additives have been
used.
• The boiler is not switched on or the water
tank is empty.
• The water tank is not fitted onto the housing
correctly.
• The steam regulator is set to the minimum
position.
d) Plug in the mains cable and set the main power switch
(6) to the "I" position.
e) Wait until the "steam ready" indicator lamp (7) lights
up.
f) If the steam station has steam regulator (4), set it to the
maximum position ("10").
g) Hold the iron over the sink or a container to collect the
water.
h) Press the steam release button (11) and gently shake
the iron. Boiling water and steam will come out, carrying
scale and or deposits that might be there. This could
take approximately 5 minutes.
i) Set the temperature selector (10) of the iron to the "max"
position, without pressing the steam release button (11).
The water in the steam chamber will start evaporating.
Wait until all the water inside the chamber has been
evaporated.
j) To clean the soleplate, immediately rub off any residue
by running the hot iron over dry cotton cloth.
Solution
• Check the mains cable, the plug and the
socket.
• Set the main power (6) button to the "I"
position.
• Set the main power (6) button to the "I"
position.
• Set the temperature control knob (10) to the
desired position.
• This is completely normal and will stop after
a short while.
• Clean the soleplate according to the
cleaning instructions in this manual.
• Reduce the steam flow when ironing at low
temperatures (Variable steam control (4)).
• Point the iron away from the ironing area
and press the steam release button (11)
until steam is produced.
• Use tap water mixed 50% with distilled or
demineralised water. If the tap water in
your district is very hard, mix tap water with
distilled water 1:2.
• Clean the sole plate with a damp cloth.
• Never add products to the boiler water.
• Set the main power (6) button to the "I"
position and/or fill the water tank.
• Fit the water tank back onto the housing
correctly (you will hear a click).
• Increase the steam flow by turning the
steam control (4).
en
13