Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required: Sealant
Fastener Kit: 75376F or 87755F
Wrenches: 10mm, 16mm, 3/4
Drill Bits: ½"
Remove in
step 3.
Figure 1.
1
Qty. (4)
½ Hex Nut
2
Qty. (4)
Conical Toothed Washer
3
Qty. (4)
½-13 X 1.75 GR5 Carriage Bolt
1.
Remove the spare tire and the foam spare tire locator from the inside the vehicle.
2.
Remove the fascia bolts and plastic fascia rivets from the fascia tabs. Remove the two rubber grommets from the trunk pan.
3.
Remove the plastic fascia bracket shown in Figure 1. and the trunk pan cover shown in Figure2. and return to vehicle owner.
Note: Trunk pan cover may be trimmed and reinstalled if required.
4.
Remove the four (2 per side) lower M10 nuts from the bumper brackets (do not discard).
5.
Raise the hitch into position with side brackets installed on the bumper bracket bolts and loosely reinstall the M10 nuts removed
in step 4.
6.
From the inside of the vehicle install the carriage bolts and 1/4 X 1.00 X 3.00 blocks through the existing holes in the trunk pan
and through the hitch. Install the conical toothed washers and hex nuts as shown above.
7.
From the underside of the vehicle, using the hitch as a template, drill the two ½" holes (1 per side) through the trunk pan.
8.
From the inside of the vehicle install the carriage bolts and 1/4 X 2.00 X 3.00 blocks through the existing holes in the trunk pan
and through the hitch. Install the conical toothed washers and hex nuts as shown above.
9.
Seal the holes in the trunk pan to prevent intrusion of exhaust fumes and water.
10.
Place the spare tire carrier and spare tire back inside the vehicle and reinstall the fascia bolts removed in step 2.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2006 Cequent Towing Products
Installation Instructions
Mercedes-Benz ML350*
Mercedes-Benz ML500*
*-Will not fit models equipped with Air Suspension Package
Fascia
Drilled Hole
Drilled Hole
Trunk Pan
Existing Nuts
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N-M)
Tighten all M10 fasteners with torque wrench to 38 Lb.-Ft. (52 N-M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3, SUV4
Bumper Bracket
Existing
Hole
4
Qty. (2)
¼ X 1.00 X 3.00 Block
5
Qty. (2)
¼ X 2.00 X 3.00 Block
Sheet 1 of 3
75376N
Part Numbers:
75376
44534
87755
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
4000 (1 816 Kg)
400 (182 Kg)
3500 (1 589 Kg)
350 (159 Kg)
Remove in
step 3.
Figure 2.
1-24-06
Rev. B
Publicité
Manuels Connexes pour Cequent Towing Products 75376
Sommaire des Matières pour Cequent Towing Products 75376
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75376N 1-24-06 Rev. B 2005, 2006 Cequent Towing Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75376N 1-24-06 Rev. B 2005, 2006 Cequent Towing Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 75376N 1-24-06 Rev. B 2005, 2006 Cequent Towing Products...