Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
FRAME RAL
FLAT WASHER
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75374F – 70755F
Wrenches: 3/4"
Drill Bits: NONE`
1
Qty. (6)
CARRIAGE BOLT 1/2-13 X 2.00 GR 5
2
Qty. (8)
FLAT WASHER 1/2
3
Qty. (6)
LOCK WASHER 1/2
1.
IF PRESENT, LOWER CARBON CANISTER FROM DRIVER'S SIDE FRAME RAIL.
2.
INSTALL FORWARD AND REARWARD CARRIAGE BOLTS AND BLOCK IN FRAME RAILS AS SHOWN.
3.
RAISE HITCH INTO POSITION AND HAND TIGHTEN FORWARD AND REARWARD FASTENERS TO BOTH RAILS AS
SHOWN.
4.
INSTALL CENTER CARRIAGE BOLT AND BLOCK IN FRAME PLACING FLAT WASHER BETWEEN RAIL AND HITCH AS
SHOWN. (DO NOT OVERLAP BLOCKS)
5.
REATTACH CARBON CANISTER IF PRESENT – CARBON CANISTER MUST NOT CONTACT BOLT HEAD, IF IT DOES,
LOOSEN CANISTER FASTENERS AND REPOSITION TO ENSURE CLEARANCE WITH BOLT HEADS.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Installation Instructions
FORD ECONOLINE VAN
E-250 & E350
STANDARD BUMPER
STEP BUMPER
Wiring Access Location: SUV1, SUV2
4
5
Tighten all 1/2 fasteners with torque wrench to 75 Lb.-Ft.
Sheet 1 of 1
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Trailer WT (LB)
Weight Distributing
Weight Carrying
Ball Mount
Illustration may not be true
representation of actual product
Qty. (6)
HEX NUT 1/2-13
Qty. (6)
BLOCK
75374N
Part Numbers:
75374
44532
70755
Max Gross
Max Tongue
WT (LB)
8000
800
6000
600
6-8-05
Rev. B
Publicité
Manuels Connexes pour Cequent Towing Products 75374
Sommaire des Matières pour Cequent Towing Products 75374
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 1 75374N 6-8-05 Rev. B 2005 Cequent Towing Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 1 de 1 75374N 6-8-05 Rév. B 2005 Cequent Towing Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 1 de 1 75374N 6-8-05 Rev. B 2005 Cequent Towing Products...