Redmond RHB-2919-E Manuel Utilisateur page 7

Start processing at a low speed to avoid splatter. Do not use the blender to
process coffee beans, ice cubes, sugar, grain, beans, and other tough meals.
Do not use the chopper bowl for blending or whisking. The central pin at the
bottom of the chopper bowl can damage the attachment. Use the beaker
provided with the appliance.
To Operate the Blender
1. Fill the beaker or a similar vessel with food.
2. Connect the blending attachment to the motor unit and turn counter-
clockwise until it clicks into place.
3. Plug in the appliance. Select the required speed setting.
4. Hold the vessel steady and place the blending attachment in the food.
Press and hold down the Power button. When processing raw vegetables,
fruits, and other hard meals turn the speed control knob to increase the
speed or press and hold down the Turbo mode button.
5. Blend foods using circular up-and-down motion.
6. After use unplug the appliance. Turn the blending attachment clockwise
to disconnect from the motor unit. Clean the appliance following the
procedure outlined in A2 section.
To Operate the Whisk
1. Fill the beaker or a similar vessel with food.
2. Insert the whisk attachment to the gear box until it clicks into place.
3. Connect the gear box to the motor unit and turn counterclockwise until
it clicks into place.
4. Plug in the appliance. Turn the speed control knob clockwise to setting
1 (minimum speed).
5. Hold the vessel steady and place the whisk attachment in the food. Press
and hold down the Power button. Turn the speed control knob counter-
clockwise to increase the speed if necessary (from 1 to 5). To whisk at a
maximum speed press and hold down the Turbo mode button.
6. Whisk the meal using clockwise circular motion.
7. After use unplug the appliance. Disconnect the attachment and the gear
box from the motor unit by turning clockwise. Clean the appliance fol-
lowing the procedure outlined in A2 section.
To Operate the Chopper (RHB-2919-E)
1. Place the chopper bowl on a flat and stable surface.
2. Fit the blade on the central pin at the bottom of the chopper bowl. Note:
the blade is very sharp, handle with caution! Always hold the blade by
the plastic collar.
All manuals and user guides at all-guides.com
3. Fill the bowl with food. Do not fill above the maximum fill mark. Follow
4. Fit the lid onto the bowl, aligning the crosspiece of the plastic collar with
5. Connect the motor unit with the chopper gear box.
6. Plug in the appliance. Select the speed setting: harder meals require
7. Steadily holding the vessel with one hand press and hold down the Power
8. After use unplug the appliance. Disconnect the motor unit. Turn the lid coun-
9. Clean the appliance following the procedure outlined in A2 section.
III. BEFORE CONTACTING SERVICE CENTER
Appliance does
not work
Strong vibration
during operation
Plastic smell
during use
IV. PRODUCT WARRANTY
We warrant this product to be free from defects for a period of 2 years from the
date of purchase. If the appliance fails to operate properly within the warranty
period and is found to be defective in material or workmanship, we will repair
or replace it free of charge. This warranty comes into force only in case an
original warranty service coupon with a serial article number and an accurate
the procedures outlined in "General Guidelines" section.
the corresponding notches in the center of the lid. Gently press the lid
down and rotate clockwise until it clicks into place.
higher chopping speed. Turn the speed control knob clockwise to increase
the speed.
or Turbo mode button. Use Turbo mode for meat and other tough meals.
terclockwise to remove. Remove the blade holding it by the plastic collar.
Problem Possible cause
Power cord is not con-
Connect the power cord to an electrical
nected to an electrical
outlet
outlet
Electrical outlet is not Connect to properly working electrical
working properly outlet
Food pieces are too large Cut food into smaller pieces
Reduce continuous operation time. In-
Appliance is overheated
crease time intervals between uses.
Appliance is new, the Thoroughly clean the appliance (refer to
smell is coming from section A2). The smell will disappear
protective cover after few uses.
RHB-2919-E, RHB-2923-E
GBR
Solution
7