Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame rail
Hitch Shown In Proper Position
Equipment Required: Pull wire (provided)
Fastener Kit: 75551F
Wrenches: 12mm, 17mm, 3/4
Drill Bits: 3/8
Modify access hole
Figure 2.
Access hole drill
location passenger
side frame rail only
1
Qty. (5)
Hex bolt M12 x 1.25 x 30mm CL 8.8
2
Qty. (6)
Conical washer 1/2"
3
Qty. (2)
Lock washer 5/16"
4
Qty. (2)
Hex bolt M8 x 1.25 x 30 CL8.8
1.
Remove tie down hook on driver frame rail. Return to owner with fasteners. Not shown.
2.
Remove fasteners holding the exhaust bracket on passenger side. Return fastener to owner. Not shown.
3.
Remove tape covering rearward hole on the passenger side frame rail and enlarge access hole. The access hole will need to
be modified before the hitch can be installed. Using a 3/8" drill bit, drill through the frame rail approx. 5/8" off the center of the
existing hole. See Figure 2 Note: Passenger side only.
4.
Feed the carriage bolt and spacer thru enlarged hole on bottom of frame rails using the pull wire. Then pull fastener back
through until fastener protrudes through bottom of frame rail. Leave pull wire on until hitch is in place. See Figure 3.
5.
Raise hitch into position. Finger tighten all M12 and 1/2" fasteners as shown.
6.
Raise exhaust hanger back into position, install new M8 fasteners. (Provided with hitch.)
7.
Tighten all fasteners to specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007, 2008 Cequent Towing Products
Installation Instructions
(
Fascia.
Figure 3.
Figure 1.
Tighten all M8 CL8.8 fasteners with torque wrench to 17 Lb.-Ft. (23 N*M)
Tighten all M12 CL8.8 fasteners with torque wrench to 65 Lb.-Ft. (88 N*M)
Tighten all 1/2 GR 5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Kia Sedona
Short wheel base only)
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Weld nuts
Fastener attach into the side
of bracket, to the tie down
2
bracket plate on the vehicle.
1
2
1
Spare tire not shown.
Exhaust pipe
5
Qty. (1)
Carriage bolt 1/2-13 X 1.50 GR5
6
Qty. (1)
Spacer
7
Qty. (1)
Hex nut 1/2-13
Sheet 1 of 3
78267 UHAUL
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
4000 (1816 Kg)
3500 (1589 Kg)
5
6
Weld nuts
Modify access hole
2
7
3
2
4
1
75551N
3-10-08
Form: F205 Rev A 5-6-05
Part Numbers:
75551
87443
44578
Max Tongue
WT (LB)
400 (182 Kg)
350 (159 Kg)
Frame rail
Rev. C
Publicité
Manuels Connexes pour Cequent Towing Products 75551
Sommaire des Matières pour Cequent Towing Products 75551
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75551N 3-10-08 Rev. C 2007, 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75551N 3-10-08 Rev. C 2007, 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75551N 3-10-08 Rev. C 2007, 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...