Atomik Miss Excite Hydroplane Manuel D'instructions page 5

ESC SETUP CONT.
ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT.
1
FULL THROTTLE
2
FULL to NEUTRAL
3
FULL THROTTLE
Tuning
Category
Running
Mode
LiPO
Cell #
Low
Voltage
Cut-off
Timing
CAUTION: LOW VOLTAGE CUT-OFF
Do not use "NO PROTECTION" when using LiPO battery packs. Monitor the battery pack temperatures after
each run. Do not allow the battery pack temperatures to exceed 120º F/ 52º C while in use. Select a higher low
voltage cut-off setting to help reduce the temperature of the battery packs. It is OK to use "NO PROTECTION"
使用
when using NiCD or NiMH battery packs.
18003
All manuals and user guides at all-guides.com
Entering Program Mode
Turn on transmitter.
Hold full throttle and connect battery.
- Continue to hold full throttle until musical tone sounds (5 seconds).
* CONTINUE TO HOLD FULL THROTTLE WHILE MOVING ON TO STEP 2*
Selecting Category
The ESC will emit a series of beep patterns. Each pattern represents a category:
1. "Beep"
2. "Beep-Beep"
3. "Beep-Beep-Beep"
4. "Beep-Beep-Beep-Beep"
To select tuning category, move throttle to neutral after desired beep pattern sounds.
*YOU ARE NOW IN THE SELECTED TUNING CATEGORY*
Selecting Value for Category
Your ESC will again emit a series of beep tones. The beep tones represent a
di erent value. (Review chart below for tone diagram).
To select a value, simply wait for the desired beep tones to emit and pull full throttle.
Move the throttle to the neutral position. Within 2 seconds you will exit program mode. If you
continue to full throttle position, you will go back to step #2 and you can select a different tuning
category.
If you are unsure if you have exited the program mode, you can disconnect
the battery and your programming will be saved.
"B" "BB"
1 Short Beep 2 Short Beeps 3 Short Beeps
Forward Forward &
Only Backward
Auto 2
Calculate Cells
No
2.8V/Cell
Protection
0º 3.75º
BEEP TONES
"BBB" "BBBB" "Beep-"
4 Short Beeps 1 Long Beep
3 4
Cells Cells
3.0V/Cell 3.2V/Cell 3.4V/Cell
7.5º 11.25º
Shaded Fields are Factory Settings (Recommended).
5
Running Mode
LiPO Cells
Low Voltage Cutoff Threshold
Timing
"Beep-B" "Beep-BB"
1 Long 1 Long
1 Short Beep 2 Short Beeps
5 6
Cells Cells
15º 18.75º 22.5º
ATOMIK-RC.COM
"Beep-BBB"
1 Long
3 Short Beeps
26.25º