Sound LAB G017F VISTA 2 Guide De L'utilisateur page 2

• Changing the fuse.
Occasionally, when the lamp fails the fuse may also blow. If this occurs, replace with a new fuse type 20mm 5mm 3.15 Amp antisurge,
high breaking capacity. This type of fuse has a ceramic case. Do not replace with any other type or value of fuse. If
fuse blows consult a dealer. The fuse is located next to the incoming mains cable.
• Focusing.
To focus slacken the two focusing controls on the top of the unit, move forwards or backwards as required, and re-tighten the screw
when the best image is obtained
• Cleaning.
The G017F should be cleaned periodically as the light output will become less intense as smoke fluid residues build up on the mirror
assembly and the lens. Also, remove any dust build up in the fan using a brush - a blocked fan can lead to overheating and reduced
lamp life. Disconnect from the mains supply and remove the cover. Clean the lens and the mirror using a soft lint-free cloth and
methylated spirit, isopropyl alcohol or hi-fi cleaning fluid. Also, make sure that the fan is not becoming obstructed.
When the G017F is switched on it will initialize the gobos, this process takes 5 seconds. The lamp will then switch on. The pattern of light
beams will move on each bass beat of the music.
With the Gobo Auto switch ON (pressed in) The gobo will change automatically on every 32nd bass beat. With the Gobo Auto switch OFF,
the gobo can be changed manually by pressing the momentary switch labelled "PRESS".
Alternatively, a momentary action footswitch may be connected to the mono 6.35mm jack socket labelled "footswitch". Connect the
footswitch to the socket on the left. When the footswitch is pressed, the gobo will change.
If more than one G017F is being used, then the footswitch may be used to change the gobos simultaneously on up to four units, by
connecting a 6.35mm jack lead from the right hand socket on one G017F, to the left-hand jack socket on then next.
Fault Finding.
Stand-alone mode.
• Does not start and go through set-up procedure.
No mains supply - check mains lead
Fuse Blown - check fuse.
• Lamp not lit
Lamp failed - replace lamp.
• Erratic response to sound
Music not loud enough.
• Light output dim.
mirror and lens dirty - clean mirror and lens.
lamp misaligned in lampholder.
lamp blackened (about to fail)
The G017F complies with the following British and European Standards:
BS EN55015 - Electromagnetic Compatibility.
BS EN60598-1 - Electrical Safety Standard for Luminaires
BS EN60598-2-17 - Safety of Luminaires for Stage and Television.
This product is guaranteed for a period of 12 months against faulty components or manufacture from the date of purchase. Upon proof of
purchase, Electrovision shall, at its own option, repair or replace the defective item at no cost to the purchaser.
This guarantee is contingent upon the proper use of the product in the application for which it is intended and does not cover products that
have been modified, subjected to unusual physical conditions, or electrical conditions outside its specification, or damaged in any way.
This guarantee is limited to the product only and does not cover carriage costs, installation costs or travel expenses. Your statutory rights
are not affected. In the event of any problems with this product contact the retailer from which it was purchased for technical assistance, or
e-mail technical@electrovision.co.uk.
GB
GB
F
F
Installateur et Utilisateurs, veuillez noter : D
D
• Ces instructions doivent être lues attentivement et conservées par l'utilisateur du produit pour une future consultation.
NL
NL
• Fixez le G017 avec le support fourni. En conformité avec les règles de Santé et Sécurité, une chaîne de sécurité doit également être
E
E
utilisée.
• Le G017 doit être installé par un électricien compétent en conformité avec les règles de câblage CEE. Branchez le G017 avec le
cordon fourni. Le code couleur du câblage est indiqué ci-après:
Marron = Phase
Bleu = Neutre
Vert/Jaune = Terre
All manuals and user guides at all-guides.com
Operation
Standards
Guarantee
IMPORTANT
Installation
the new