American Standard Antiquity Cadet 3 2907 Instructions D'installation

INSTALLATION INSTRUCTIONS
ANTIQUITY CADET
COMPACT CADET
COMPACT CADET
Model 2568 – Compact Elongated Right Height® with Seat
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly,
please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your
installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver
Hacksaw Wax Ring/Gasket
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
ROUGHING-IN DIMENSIONS NOTE: Distance from wall to closet flange centerline must be as listed below:
2
FINISHED WALL
737mm
(29")
225mm
(8-7/8")
C/L OF SEAT POST
HOLES 140mm
(5-1/2) CENTERS
462mm
(18-3/16)
419mm
(16-1/2)
235mm 360mm
(9-1/4)
(14-3/16)
305mm
C/L OF OUTLET
(12")
3
CLOSET FLANGE
CLOSET BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 ° , and slide
into place 6" (152 mm) apart and parallel to wall.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 11
® 3 - 1.6 GPF ONE-PIECE TOILET, MODEL 2907
®
3 - 1.6 GPF ONE-PIECE TOILET
® ®
3 FloWise - 1.28 GPF ONE-PIECE TOILET
Adjustable Wrench
Flexible Supply Tube
ANTIQUITY CADET 3
457mm
(18")
C/L
127mm
(5 " )
C/L OF SUPPLY
276mm
AS REQUIRED
(10-7/8)
A
Sealant
Closet Bolts
FINISHED WALL
16 ± 6mm
(5/8 ± 1/4)
159mm
(6-1/4)
714mm
(28-1/8")
267mm
FINISHED
(10-1/2)
FLOOR
305mm
(12)
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and install wax
ring evenly around waste flange (horn), with tapered end of ring
facing toilet. Apply a thin bead of sealant around toilet base.
Tape Measure
Carpenters Level
COMPACT CADET 3
724mm
(28-1/2)
381mm
(15)
C/L OF SEAT
POST HOLES
140mm (5-1/2)
CENTERS
422mm
(16-5/8)
419mm
(16-1/2) SUPPLY
AS
REQ'D
292mm
140mm
*
241mm
(11-1/2) (5-1/2)
(9-1/2)
C/L OF OUTLET
394mm
(15-1/2)
7301270-10 0 Rev. E
724mm
(28-1/2)
FINISHED
FLOOR
WAX RING