Armacost Lighting 523121 Mode D'emploi

Wall-Mount Wireless Touchpad
for White LED Dimmers
Item 523121
Compatible with: items 511123, 511129, 513115
■
Includes: touchpad, mounting screws, drywall anchors, & battery
■
For dry location use only
■
Operating range of up to 100 ft. depending on environment
■
Features RF pairing
technology for expandability
and multi-zone lighting
control. This remote
wireless touchpad can
be paired to control and
synchronize multiple
dimmer receivers in the
same area, or multiple
touchpad/receiver sets can
control different zones of
lighting in the same area
without cross interference.
WIRELESS TOUCHPAD TRANSMITTER INSTALLATION
Surface mount touchpad
transmitter or install in wall.
Designer-style wall plate and
screws are included.
Note: Compatible with most,
but not all, switch plates made
by other manufacturers.
Easily mount to any Can be installed in standard
wall or fl at surface electrical boxes, or by using
(screws and anchors
included).
LOW-VOLTAGE
DC POWER SUPPLY
120V AC
12V or
Plug in
24V DC
or
direct wire
OPERATION AND PAIRING
1. Make sure the dimmer is installed and properly working. When pairing,
be within 10 feet of the dimmer (receiver).
2. Disconnect power to the dimmer by unplugging or switching off the
power supply. Leave off for at least 5 seconds. You can also disconnect
power by pulling out the green block connector on the dimmer.
On/off key
(press and hold,
do not tap)
Press and hold
to increase
brightness
Press and hold
to dim lighting
Some electrical boxes
may require the
removal of tabs as
shown, simply break
away with wire cutters.
Voltage Wall
a low voltage wall plate Plate Mounting
mounting bracket.
LED TAPE LIGHT
DIMMER
12V or
24V DC
LED PUCK LIGHTS
WIRELESS
TRANSMITTER
3. To pair, press and hold the on/off and
brightness down keys simultaneously.
While continuing to hold the buttons, restore
power to the power supply and dimmer.
To test, press the on/off key of the wireless
touchpad to confi rm that it can control the
receiver. If not, repeat the process.
Depending on the lighting layout, and to reduce
the need for extra wiring, it can be advantageous
to have one touchpad control or be "paired" to
multiple rotary knob dimmer receivers (wireless
ready models only).
To add or pair more receivers, repeat the same
process with additional receivers. The wireless
touchpad will pass its unique code to
multiple receivers.
To synchronize multiple receivers,
so that all lights turn on/off and dim
in unison to one touchpad, simply
manually turn off all receivers with
each rotary knob. Then press the power
on key of the wireless touchpad. All
lights should turn on at the same time.
Note: You can also "un-pair" the
dimmers by following the process
above, but press the power on and
brightness up keys instead.
IMPORTANT: Do not press any key on
the wireless touchpad repeatedly or
too quickly or the receivers can lose
synchronization or fail to operate in
unison. Firm, deliberate button presses
are required to keep multiple dimmers
in synch. For effective synchronization,
all receivers must be within range of
the single wireless touchpad.
TROUBLESHOOTING
The wireless touchpad does not work.
Be sure the wireless touchpad is in range of the receiver. Try moving the
touchpad closer to the receiver. The dimmer is a radio frequency (RF)
device and, as such, the range of the wireless remote control is dependent
on many factors. Actual operational distance will vary based on walls and
line of sight obstructions, and other nearby electronic devices.
Be sure your battery is good. Replace the battery if in doubt. A battery will
last from 6 months up to 2 years, depending on usage.
The receiver may need to be paired again with your transmitter.
If the dimmer receiver is functioning properly, and the touchpad battery
is fresh, yet the touchpad will not control the lighting, repeat the pairing
instructions.
SPECIFICATIONS
Wireless working frequency ...................................................433.92Mhz
Operating temperature ...................................................32° F to 100° F
Typical Low
Transmitter battery .......................................................... CR2032 3-volt
FCC ID .......................................................................... NWKHF10008
Bracket Country of origin ...........................................................................China
1-year limited warranty. Improper installation, improper powering,
abuse, or failure to use this device for its intended purpose will void
warranty. Proof of purchase is required for all returns. Questions?
Email support@armacostlighting.com.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation. Changes or modifi cations to this unit not
expressly approved by the party responsible for compliance could void the user
authority to operate the equipment.
© 2012-21 Armacost Lighting.
All rights reserved.
211007