Maintenance And Adjustments; Service & Repair Information - Jiffy 4G Mode D'emploi

STARTING-OPERATION-STOPPING INSTRUCTIONS
COLD STARTING PROCEDURE: Starting engine for the first time or
after engine has cooled off or after running out of fuel.
1. Press primer bulb until gas (return) line is free of bubbles.
2. Check to make sure the rocker switch is in the RUN (ON)
position
3. Move choke lever to FULL CHOKE or (I\I) position.
(operator's left)
4. Depress throttle control with left hand and grasp the starter
handle in your right hand.
5. Slowly pull starter handle until you feel resistance from
engine, then pull vigorously with short quick pull,
ONCE.
6. Move choke lever to HALF CHOKE and pull starter handle
to start.
7. If engine doesn't start after 5-6 pulls, press the primer bulb
5-10 times and repeat with steps 5-6.
8. After engine starts running, move choke lever to OFF
position until engine runs smoothly. Leave in half choke
position in extremely cold weather.
9. To stop engine, push rocker switch to OFF or (O) position.
SPECIAL NOTE: If the engine does not start due to extremely cold
temperatures, move unit to warm environment, remove spark plug and
wipe off excess fuel, replace spark plug and repeat steps 1 thru 8.
Please view starting video on Jiffy website
www.jiffyonice.com
USING YOUR JIFFY 4G ICE DRILL
NOTE: To minimize water splash, back-off throttle when the
drill breaks thru ice, then raise drill slowly.
NOTE: The clutch slips when the drill is overloaded, when this
happens, raise complete unit slightly to ease load.
NOTE: Remove blade protector from drill assembly prior to
drilling. Reinstall when drilling is complete.
NOTE: If drilling additional holes, carry unit in upright
position by handles only, to next location and proceed
with normal starting and operating instructions.
1. When all holes have been drilled, and engine is stopped, lay
unit down, resting on wing handle with engine spark-plug facing
upward. Disconnect drill assembly from powerhead by sliding
E-Z Connect™ Collar down and pulling clevis pin from drill
assembly. Do not remove pin from collar tether. Slip drill
assembly off of engine output shaft, then re-insert clevis into
drill assembly and slide E-Z Connect™ Collar up to cover clevis
pin.
2. Reattach blade protector to drill assembly to prevent damage to
the blade teeth and point.
TRANSPORTING AND STORAGE
1. Disconnect spark plug wire from spark plug and keep it away
from spark plug.
2. Make sure all fuel is drained from fuel tank, and fuel cap is
screwed on tight.
3. Always transport and store powerhead in an upright position
and make sure powerhead and drill assembly are properly
anchored to prevent damage.
4. Never store powerhead with fuel in tank indoors or in enclosed,
poorly ventilated enclosures where fuel fumes may reach an
open flame, spark or pilot light as on a furnace, water heater,
clothes dryer, etc.
5. Always transport and store powerhead with powerhead in
an upright (operating) position or engine spark-plug facing
upward. Make sure powerhead and drill assembly are
properly anchored to prevent damage.
All manuals and user guides at all-guides.com
-4-

MAINTENANCE AND ADJUSTMENTS

Check SPARK PLUG, periodically.
1. Before removing plug, wipe dirt and debris from spark plug base.
2. Remove and inspect spark plug for carbon build up.
3. Replace spark plug if electrodes are pitted, burned, or porcelain is
cracked. For replacement use: Autolite® 4194 spark-plug or
equivalent. Failure to use proper spark-plug may result in engine
damage.
4. Check spark-plug gap with wire feeler gauge and set gap at .025".
5. Install spark plug in engine and tighten securely.
Check THROTTLE CONTROL AND CABLE periodically for proper
operation. If needed, use silicon spray to lubricate throttle cable. DO NOT
use WD-40 because it will freeze.
AIR FILTER – The engine has an air cleaner which helps prevent premature
engine wear and failure. Never run an engine without a complete, clean air
filter properly installed. Clean or replace air filter as
REPLACEMENT TEETH – Improper cutting may be due to dull or damaged
drill teeth or drill point. Maintain sharp blade teeth and point. Preserve the
original factory cutting angles when sharpening your drill. File blade teeth
and use a disk sander to sharpen the point. Only genuine Jiffy® blade teeth
are to be used.
SERVICE & REPAIR INFORMATION
BLADE TEETH REPLACEMENT INSTRUCTIONS – When replacing blade
teeth, the beveled edge of teeth and the head of the capscrews should face
the ice. The stamped part number on the teeth should face away from the
ice, as shown in the diagram. Use two 7/16" wrenches to remove the
capscrews. When attaching blades, finger tighten all fasteners, then fully
tighten with wrenches.
CAUTION – THE BLADE TEETH ARE SHARP AND SHOULD BE
HANDLED CAREFULLY TO AVOID FLESH CUTS OR INJURY.
ENGINE SPEED – NEVER TAMPER WITH ENGINE SPEED
CONTROL SYSTEM, OVERSPEEDING THE ENGINE CAN BE
DANGEROUS AND MAY CAUSE PERSONAL INJURY OR DAMGE
TO UNIT. TAMPERING WITH ENGINE SPEED CONTROL SYSTEM
WILL VOID ENGINE WARRANTY.
For engine adjustments, repairs or warranty service not covered in this
manual, visit our web site at www.jiffyonice.com, visit one of our authorized
Jiffy service dealers or call our customer service number at 800-344-0712
Monday – Friday from 7:00 a.m. to 4:30 p.m. CST.
warranty service, Jiffy® ice drill proof of purchase (sales receipt) establishes
the date of sale and the start of the warranty period.
needed.
When requesting