Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36516F
Wrenches: 10mm, 19mm,
Extension, Large screwdriver
Drill Bits: None
Frame Rail
1
2
3
Note:
Fasteners Typical
Both Sides
Figure 1
1 1 1 1
Qty. (6)
Flat Washer, 1/2"
2 2 2 2
Qty. (6)
Lock Washer, 1/2"
For vehicles with appearance panel: Remove appearance panel which covers the trunk pan. This panel will need to be trimmed or not reinstalled
on vehicle. Ask vehicle owner their choice before starting installation. See Figure 2
1.
Remove plastic plugs, from existing holes (if present).
2.
Raise hitch into position over the exhaust pipes aligning the slots in the hitch with the weldnuts in the bottom of the frame rails. NOTE:
Lowering exhaust may ease installation. Spraying a lubricant on the metal hanger rod and the rubber isolator helps removal.
3.
Install fasteners as shown above.
4.
Torque all fasteners to specifications shown below.
5.
Raise exhaust back into position, if lowered prior to hitch installation.
6.
Reinstall trimmed cover panel removed. Or return untrimmed panel to vehicle owner.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
c 2013,2015 Cequent Performance Products - Printed in Mexico
Installation Instructions
Toyota Sienna
Fascia
(Sold separately)
Drawbar Kit:
36061
Drawbar must be used in the
Rise position only.
6" Ratchet
Existing
Weldnut
3 Places
(Both
Sides)
Tighten all M12 CL10.9 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, 2
Sport Model
Area to be trimmed
3 3 3 3
Qty. (6)
Hex Bolt, M12 x 1.25 x 40mm
Sheet 1 of 3
36516N
Part Numbers:
36516
90217
06140
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
3500 (1589 Kg)
300 (136 Kg)
To be reinstalled
Area to be trimmed
Figure 2
To be reinstalled
10-13-15
Rev. D
Publicité
Manuels Connexes pour Cequent Performance Products 36516
Sommaire des Matières pour Cequent Performance Products 36516
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. c 2013,2015 Cequent Performance Products - Printed in Mexico Sheet 1 of 3 36516N 10-13-15 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75696N 10-13-15 Rev. D 2012,2015 Cequent Performance Products - Imprimé au Mexique...
- Page 3 Este producto cumple con las especificaciones y requerimientos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Página 3 de 3 36516N 10-13-15 Rev. D c 2013,2015 Cequent Performance Products - Impreso en México...