Cequent Performance Products 24916 Instructions D'installation

Frame rail
Fascia
Hitch Shown In Proper Position
Equipment Required: Lubricant or soapy water
Fastener Kit: 24916F
Wrenches: 10mm, 11/16"
Drill Bits: None
q
Kink Pull wire to keep spacer
independent of bolt
Example of pull wire procedure
Rearward carriage bolt and
spacer with pull wire
j
Qty. (1) U-Bolt 3/8-16 GR2
k
Lock washer 3/8"
Qty. (2)
l
Qty. (2) Hex nut 3/8-16
m
Qty. (4) Carriage bolt 7/16-14 X 1.50 GR5
1. Lower exhaust for ease of installation. Lower exhaust system at the rubber isolator. Spraying a lubricant or soapy water on the metal hanger rod
and the rubber isolator helps with removal. Do not let the exhaust drop, support the exhaust during installation.
2. Remove bolt from bracket on drivers side, attached to the hoses, for existing access hole for fasteners.
3. Install the fasteners in the frame rails. Install the rearward fasteners first. Feed spacers and carriage bolts into position using the pull wires
provided into each frame rail through the access holes. Leave pull wire attached. Note: It is much easier if bolt and spacer are not engaged
while inserting them into frame, refer to illustration.
4. Install U-bolt on the tie down hook.
Raise hitch into position (feed pull wires through the slot on the hitch). Remove the pull wires and attach the 7/16" conical and hex nut loosely to
5.
hitch for support.
6. Install tie down fasteners as shown.
7. Torque all fasteners to specifications shown below
8. Reinstall bolt from drivers side, for the hose bracket. (Step 2)
9. Raise exhaust back into position using an lubricant or soapy water.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
©
2014, 2015 Cequent Performance Products, Inc
Printed in Mexico
Installation Instructions
Mitsubishi Mirage
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
Bracket for hoses
driver's side only
Existing access
hole behind hoses
Tighten all 3/8-16 GR2 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M)
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Existing
access hole
Existing vehicle hoses
Note: Fasteners typical
both sides
Tie down
j
k
l
n
Spacers 1/4" X 7/8" x 3"
Qty. (4)
o
Conical washer 7/16"
Qty. (4)
p
Qty. (4) Hex nut 7/16-14"
q
Pullwire 7/16"
Qty. (4)
Sheet 1 of 3 24916N
Part Numbers:
24916
60348
77303
24484UH
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Wiring Access Location: PC3, 4
Rearward
m
n
Frame rail
o
p
q
10-05-15
Form F206 Rev B 9-17-2012
Existing
access hole
Rev. C