Cequent Performance Products 36545 Instructions D'installation

Frame rail
Hole for cable
tie to secure
vehicle cable
wires
Hitch Shown In Proper Position
Equipment Required: Pull wires(provide), safety glasses.
Fastener Kit: 36545F
Wrenches: 7/8", screwdriver or trim panel tool
Drill Bits: None
Figure 2
B. Align block on
A. Insert bolt and
access hole
Block into frame
Figure 3
Reverse Pull wire Method
1 1 1 1 Qty. (4) Carriage bolts ½-13 x 1.75 GR8
2 2 2 2
Qty. (4) Spacer ¼" x 1" x 3"
3 3 3 3 Qty. (4) Conical washer ½"
1. Remove rubber square plug (1) in each frame rail. Return to owner.
2. Detach vehicle wiring plastic fasteners from around frame rail (3) places each side, using a screwdriver or trim panel tool.
3. Feed carriage bolts and spacers through square access holes into the rearward holes in frame, using the pull wires. Each side.
See Figure 2. Leave pull wire attached.
4. Using the reverse pull wire method, feed remaining carriage bolts and spacers (item 2) into frame rail. Each side. See Figure 3.
5. Raise the hitch into position keeping the vehicle wiring clear of the hitch, and feeding the pull wires though the adjacent holes on
the hitch.
6. Carefully remove pull wires on the forward attachment. One at a time place the washer over the pull wire and use it to hold the
bolt in place while carefully removing the pull wire, then attach the hex nut.
7. Carefully remove pull wires on the rear attachment. One at a time place the spacer (item 5) pull wire and use it to hold the bolt in
place while carefully removing the pull wire, then attach the washer and hex nut.
8. Tighten all fasteners to the required torque specification.
9. Using the cable ties secure the vehicle wiring to the forward hole on the side of the hitch bracket with the cable ties.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2014, 2015 Cequent™ Performance Products, Inc.
Printed in Mexico
Installation Instructions
Does not fit 2015 and later V-6 models
Fascia
Drawbar must be used in the
Rise position only.
Note: Fasteners typical
both sides
C. Pull bolt thru
block
Pull wire
Tighten all ½-13 GR8 fasteners with torque wrench to 110 Lb.-Ft. (149 N*M)
Jeep Cherokee
Does not fit TrailHawk
(Sold separately)
Do Not Exceed Lower of Towing Vehicle
Drawbar Kit:
36061
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
1 1 1 1
5 5 5 5
1 1 1 1
2 2 2 2
Hitch
bracket
3 3 3 3 5 5 5 5
4 4 4 4
Figure 1
4 4 4 4 Qty. (4)
5 5 5 5
Qty. (2)
6 6 6 6 Qty. (2)
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Wiring Access Location: SUV 1&2
2 2 2 2
Square access
hole
Frame rail
Hex nut ½-13 GR8
Spacer ¼" x 1-1/2" x 2"
Cable ties
36545N 10-9-15
Form: F205 Rev C 9-17-2012
36545
90239
06166
Vehicle
Forward
6 6 6 6
3 3 3 3
4 4 4 4
Rev. C