Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Backguard Installation
Model
Low Back
36''
PA36JLBG
48''
PA48JLBG
48'' Steam
PA48JLBSG
When using the Flush Island Trim, THERMADOR
recommends a minimum 12'' (305 mm) rear clearance to a
combustible surface. Clearances from non-combustible
materials are not part of the ANSI Z21.1 scope and are not
certified by CSA. Clearances of less than 12'' (305 mm)
must be approved by the local codes and/or by the local
authority having jurisdiction.
WARNING
State of California Proposition 65 Warnings:
This product contains chemicals known to the State of
California to cause cancer, birth defects or other
reproductive harm.
WARNING
Fingers or hands could get pinched when installing the
backguard. Severe injury could result. Use extreme
caution and wear thick protective gloves to avoid
potential laceration to finger or hand while sliding the
backguard down onto the range.
Low Back Parts Included
1 – Low Back panel
8 or 9 – T-20 Torx stainless screws
8 or 6 – T-20 Torx drill point screws
Tools Needed
T-20 Torx head screwdriver or drill
Protective Work Gloves
English 1
Backguard and Toe Kick
Installation Instructions
Flush Island Trim
Included on Range
Included on Range
Included on Range
9001078742 • Rev. A • 5U06U8 • © BSH Home Appliances Corporation, 05/15
Removing the Flush Island Trim
1. Depending on model, remove the (3) or (4) T-20 Torx
stainless screws in the front face of the included Flush
Island Trim.
2. Remove the (4) drill point screws securing the trim to
the side panels, and the (2) to (4) drill point screws
securing the piece to the back panel. Lift up to fully
remove.
Publicité
Manuels Connexes pour Thermador PA36JLBG
Sommaire des Matières pour Thermador PA36JLBG
- Page 1 48'' Steam PA48JLBSG Included on Range When using the Flush Island Trim, THERMADOR recommends a minimum 12'' (305 mm) rear clearance to a combustible surface. Clearances from non-combustible materials are not part of the ANSI Z21.1 scope and are not certified by CSA.
- Page 2 Installing the Lowback Remove the Front Foot Cover Assemblies 3. Align the back panel of the new accessory with the 1. Remove the (2) T-20 Torx head screws securing the flanges on the range side panels right and left rear foot cover assembly to the range base, as shown in the corners.
-
Page 3: Installation Du Dosseret
48 po à vapeur PA48JLBSG Inclus Lors de l'utilisation de la garniture d'îlot THERMADOR, il faut un espace minimal de 12 po (305 mm) entre la partie arrière de l'appareil et la surface combustible. Les espaces libres jusqu'aux surfaces non combustibles ne sont pas précisés dans la norme ANSI Z21.1 et ne sont pas certifiés... - Page 4 Installation du dosseret bas Retrait des garnitures des pattes avant 3. Alignez le panneau arrière du nouvel accessoire avec 1. Enlevez les deux vis Torx T-20 qui retiennent la les brides des coins arrière droit et gauche des garniture de la patte à la base de l'appareil, comme panneaux latéraux de la cuisinière.
- Page 5 Incluida 48 pulg. al vapor PA48JLBSG Incluida Cuando se utiliza el adorno de isla THERMADOR, hace falta un espacio libre trasero mínimo de 12 pulg. (305 mm) entre el aparato y la superficie combustible. Los espacios libres para las materias no combustibles no forman parte de la norma ANSI Z21.1 y no están certificados por la CSA.
- Page 6 Instalación de la consola trasera baja Quitar los adornos de las patas delanteras 3. Alinee el panel trasero del nuevo accesorio con las 1. Quite los dos tornillos Torx T-20 que sujetan el adorno pestañas de los rincones de izquierda y derecha de los de la pata a la base del aparato, como se muestra en paneles laterales.