Technical Data - Westfalia 06207 Mode D'emploi

EN
Setting up the spotlight
1. Unpack the items supplied and remove all protective fi lms that
may be present. Check all parts for possible transport dam-
age. If you should fi nd any transport damage, do not use the
article(!), but contact the customer service department imme-
diately.
3. Position the spotlight a distance of no more than 10 metres
from the object onto which the laser beam is to be projected.
Anchor the ground spike in the ground (if indoors: in a fl ower
pot).
4. Orient the spotlight towards the object. To do this, you can
loosen the clamping screw and tighten it again after you have
oriented the spotlight.
5. Lay the mains cable in such a way that it does not present a
trip hazard.
7. Only connect the mains adapter to a plug socket that has been
properly installed.
Assembly the wall bracket
CAUTION!
■ The wall and the installation materials (not supplied) must be
able to bear the weight of the fl oodlight.
■ Make sure that you do not drill into or destroy any pipes or
cables. Find out where possible pipes or cables may run
and avoid them.
1. Hold the wall bracket against the wall and mark the position of
the holes. Make sure that the markings are horizontal.
2. Drill the holes.
3. Attach the wall bracket to the wall with suitable screws and if
necessary wall plugs (not supplied).
4. Attach the spotlight to the wall
Use
1. Before you use the remote control for the fi rst time, pull the
insulation strip out of the battery compartment to activate the
battery.
2. If the spotlight does not switch on automatically after you have
connected it, point the remote control at the front of the spot-
light and press the EIN (on) button.
Point the remote control directly at the front of the spotlight.
The distance between the remote control and the spotlight
should be no more than 3 metres.
Under sub-zero temperatures it can take a few minutes un-
til the spotlight lights up fully.
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •
*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.
06207_DE-EN-FR-NL_A4_V1.indb 4 06207_DE-EN-FR-NL_A4_V1.indb 4
2. Attach the ground spike to the spot-
light: place the nut into the hexago-
nal hole in the ground spike holder.
Place the round end of the ground
spike into the ground spike holder
and fasten it with the clamping
screw.
6. Plug the cable connector into the
socket on the mains adapter that is
also supplied. Then twist the cap nut
onto the thread of the mains adapter.
bracket.
Customer Service / Importer:
3. By pressing the buttons of the remote control, you can call up
the following functions:
6
11
10
10 Speed: + increase, - reduce (to deactivation point)
11 Color select: select the type of lighting
AUTO All types of lighting run sequentially through
If the spotlight stops responding to the remote control, it is possible
that the cover may be dirty or the battery may be too weak and
need to be replaced (see below).
Changing the Battery of the Remote Control
pull
press
3. Push the battery compartment back into the remote control to
the limit stop.

Technical Data

Product number:
Spotlight
Model number:
Voltage supply:
Degree of protection:
Mains adapter
Model number:
Voltage supply:
Protection class:
Degree of protection:
Remote Control
Voltage supply:
Range:
Disposal
The packaging material is recyclable. Please dispose of it in
an environmentally friendly manner.
Dispose of the article in an environmentally friendly manner.
It should not be disposed of in the normal household waste.
Please dispose of it at a recycling centre for used electrical
and electronic devices.
Non-rechargeable and rechargeable batteries should be
removed prior to disposal of the article and disposed of
separately from the article. To protect the environment, non-
rechargeable and rechargeable batteries may not be dis-
posed of with normal household waste, but must be taken
to suitable collection points. Also note the relevant statutory
regulations governing the disposal of batteries.
✆
All rights reserved.
Instructions
6 Switch on / off
7 Brightness: ˄ increase, ˅ reduce
7
8 Flash choosen type of lighting
fl ashes
8
9 Timer buttons 3, 5, 8 (fi rst press
the On- / Off-button and select a
type of lighting, then press the timer
9
button): Daily light-up time of the
laser in hours (24-hours-mode).
Example: If you select 3, the la-
ser switches off after 3 hours and
switches on again after 21 hours.
STOP switch off timer
1. The battery compartment is located
on the narrow side of the remote
control. Pull it out as shown.
2. Take the used battery out and insert
a 3 V battery of the CR2025 type.
The positive pole must be facing up-
wards.
06207
LPS-GD-05LED
3.5 V DC
IP65
RKPO-EU0351200
100 – 240 V~ 50/60 Hz
II
IP44
3 V DC (1 x button cell, CR2025 type)
approx. 3 metres
+49 38851 314650 *)
Z 06207 M DS V1 0916
14.09.2016 16:29:41 14.09.2016 16:29:41