Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Bumper bracket
Bumper
Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 41935F
Wrenches: 17mm, 19mm, 21mm
Drill Bits: None
Existing M12-1.25
bolts, (4) total.
Remove existing
brackets both sides.
Return to owner.
1
Qty. (4)
1/2" Conical washer, toothed.
2
Qty. (4)
M14-1.50 Flanged hex nut
3
Qty. (8)
9/16" Helical lock washer
1.
Remove existing angle brackets, both sides, between truck frame rails and truck bumper brackets. Return to owner.
Save bolts as they will be reinstalled in Steps 2 & 3.
2.
Raise hitch into position as shown and reinstall M14 bolts removed in Step 1through hitch and bumper bracket. Bolts must face
outwards as shown. Place 9/16" flat washers, lockwashers and M14 flanged hex nuts on these bolts on outside of truck bumper
bracket. Hand tight only.
3.
Place a toothed conical washer over each M12 bolt removed in Step 1, and then reinstall M12 bolts through hitch and into
weldnuts in truck frame. Hand tight only.
4.
Install M14-1.50 bolts supplied through 9/16" helical lockwashers and blocks. Install these through hitch and then through blocks
into frame weldnuts, typical (4) places. Hand tight only.
5.
If existing electrical bracket on bottom of truck bumper contacts top of hitch tube, then bend up out of the way. It may be
necessary to cut bolts holding electrical bracket shorter so that bracket can be pushed up farther.
6.
Torque M12 bolts to specifications below first. Then torque M14 bolts in bumper brackets to specifications below next.
Torque M14 bolts forward on frame to specifications below last.
Torque all M12 fasteners with torque wrench to 130 lb.-Ft.(176 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007 Cequent Towing Products
Installation Instructions
Toyota Tundra
Existing weldnuts
in frame
1
Existing M14-1.50
bolts, (4) total.
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
Place blocks
outside of frame and hitch.
4
Qty. (4)
9/16" Flat washer
5
Qty. (4)
M14-1.50 X 45mm Cl. 10.9 Hex bolt
6
Qty. (8)
1/4" X 1-1/2" X 2" Block
Torque all M14 fasteners with torque wrench to 148 lb.-Ft. (201 N*M)
41935N
Part Numbers:
41935
Max Gross
Max Tongue
Trailer WT- lb (Kg)
WT- lb (Kg)
14,000 (6356)
1400 (636)
12,000 (5448)
1200 (545)
6
between
ALL FASTENERS
TYPICAL BOTH SIDES.
5
3
2
4
03-20-07
Form: F205 Rev A 5-6-05
3
6
Rev. A
Publicité
Manuels Connexes pour Cequent Towing Products 41935
Sommaire des Matières pour Cequent Towing Products 41935
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 41935N 03-20-07 Rev. A 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 41935N 03-20-07 Rev. A 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 41.935N 03-20-07 Rev. A 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...