Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75527F
Wrenches: 17mm, 19mm, 22mm, 3/4, 7/8
Drill Bits: None
Bumper Bracket
Fasteners Typical Both Sides
1
Qty. (4)
M12 X 1.25 CL9.8 X 40mm Hex Bolt
2
Qty. (6)
Conical Toothed Washer
3
Qty. (4)
M14 X 2.00 CL10.9 X 40mm
4
Qty. (4)
5/8 Flat Washer
5
Qty. (4)
5/8 Lock Washer
1.
Remove angle brackets from the inside surface between the frame rails and the bumper brackets.
2.
Raise hitch into position and install M12 bolts and conical toothed washers into existing weldnuts.
3.
Install M14 bolts through the vehicle bumper bracket, through the hitch and fasten with flat washer, lock washer, and hex nut.
4.
Install 1/2-13 hex bolts and 1/4 block through the bumper bracket, through the hitch and fasten with conical toothed washers
and hex nuts.
5.
Tighten all fasteners to the required torque specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2011 Cequent Performance Products
Installation Instructions
Toyota Tundra
Bumper
Angle Bracket
Both Sides
Frame Rail
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all M12 X 1.25 CL9.8 fasteners with torque wrench to 105 Lb.-Ft. (142 N*M)
Tighten all M12 X 1 25 CL9 8 fasteners with torque wrench to 105 Lb Ft (142 N*M)
Tighten all M14 X 2.00 CL10.9 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)
Do Not Exceed Lower of Towing Vehicle
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
6
Qty. (4)
M14 Hex Nut
7
Qty. (2)
1/2-13 X 1.75 Hex Bolt
8
Qty. (2)
1/4 X 1.00 X 2.00 Block
9
Qty. (2)
1/2 Hex Nut
Sheet 1 of 3
75527N
Part Numbers:
75527 44568
87434 78222
Max Gross
Trailer WT (LB)
8000 (3632 Kg)
6000 (2724 Kg)
Existing Weldnuts
4/18/11
Max Tongue
WT (LB)
800 (363 Kg)
600 (272 Kg)
Rev. B
Publicité
Manuels Connexes pour Cequent Performance Products 75527
Sommaire des Matières pour Cequent Performance Products 75527
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75527N 4/18/11 Rev. B 2011 Cequent Performance Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75527N 4/18/11 Rev. B 2011 Cequent Performance Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75527N 4/18/11 Rev. B 2011 Cequent Performance Products...