Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required: Small Flat Head Screwdriver, Phillips head
Fastener Kit: 75586F
Wrenches: 10mm, 14mm, 17mm
Drill Bits: None
Fasteners typical
Both sides of Vehicle
1
Qty. (6)
Hex Bolt – M10 x 1.25 x 30mm CL10.9
1.
Remove plastic appearance panels which cover driver's and passenger's side frame rails. Return appearance panels and
fasteners to vehicle owner.
2.
Remove tow hooks from each frame rail and return hooks and fasteners to vehicle owner.
3.
Raise hitch into position and install fasteners as shown.
Tighten all M10 x 1.25 CL10.9 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle
and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2007, 2009, 2011 Cequent Performance Products
Installation Instructions
Toyota Highlander Hybrid
Will not fit with full size 19" spare.
Fascia
Screwdriver
1
2
Tighten all M10 x 1.25 CL10.9 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Tighten all M10 x 1 25 CL10 9 fasteners with torque wrench to 42 Lb Ft (57 N*M)
Toyota Highlander
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3, SUV4
Existing weldnuts in
Vehicle frame
2
Qty. (6)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
5000 Lb. (2270 Kg)
5000 Lb. (2270 Kg)
Conical Toothed Washer – 3/8"
75586N
4-21-11
Part Numbers:
75586
44587
87452
Max Tongue
WT (LB)
500 Lb. (227 Kg)
500 Lb. (227 Kg)
12
Rev. E
Publicité
Manuels Connexes pour Cequent Performance Products 75586
Sommaire des Matières pour Cequent Performance Products 75586
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75586N 4-21-11 Rev. E 2007, 2009, 2011 Cequent Performance Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75586N 4-21-11 Rev. E 2007, 2009, 2011 Cequent Performance Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75586N 4-21-11 Rev. E 2007, 2009, 2011 Cequent Performance Products Form: F205 Rev A 5-6-05...