Télécharger Imprimer la page

Goldenrod Water-Block 496 Instructions D'installation

Publicité

Liens rapides

IMPORTANT:
Always mount
cutoff valve between filter and tank!
FUEL
TANK
WRENCH
LOCATION
INLET
FILTER
TOP CAP
NO.
470-³⁄₄ or
470-1
GASKET
NO. 202204
FILTER ELEMENT
NO. 496-5
FILTER
BOWL
NO.
495-4
Drawing No.
202594F 4/13
IMPORTANTE:
¡Siempre se debe
montar la válvula de corte entre el filtro
y el tanque!
TANQUE DE
COMBUSTIBLE
POSICION
DE LLAVE
DE TUERCAS
ENTRADA
TAPA
SUPERIOR
DE FILTRO
N° 470-³⁄₄
O 470-1
EMPAQUE-
TADURA
N° 202204
ELEMENTO DE
FILTRO N° 496-5
TAZON
DE FILTRO
N° 495-4
Dibujo N°
202594F 4/13
NO. 496
FUEL TANK FILTER
NOTE:
not absorb water from fuel
containing alcohol.
OUTLET
CAUTION:
THIS TANK FILTER IS DESIGNED
FOR USE WITH GASOLINE, GASOHOL,
DIESEL OR 20% BIODIESEL (B20) FUELS.
IT IS NOT RECOMMENDED FOR USE WITH
100% BIODIESEL (B100). USE WITH OTHER
CHEMICALS COULD RESULT IN STRESS
CRACKS AND LEAKAGE.
FILTRO PARA
TANQUES DE
COMBUSTIBLE
N° 496
SALIDA
PRECAUCION:
ESTE FILTRO DE TANQUE
HA SIDO DISEÑADO PARA USARSE
CON GASOLINA, GASOLINA CON ALCOHOL,
DIESEL O BIODIESEL AL 20% (B20). NO SE
RECOMIENDA PARA USO CON BIODIESEL AL
100% (B100). SI SE USAN OTROS PRODUCTOS
QUIMICOS SE PUEDEN PRODUCIR ROTURAS
POR ESFUERZO Y FUGAS.
INSTALLATION INSTRUCTIONS
Attach filter top cap to storage tank valve on opening
marked "IN". Be sure there is a shutoff valve between filter
and tank. Attach hose and nozzle to filter opening marked
"OUT". CAUTION: Do not tighten filter cap using the filter
bowl for leverage. Apply wrench to flat surfaces in center part
of filter cap to tighten or remove. See illustration.
When installing the element and bowl, apply a coating
of oil to each side of gasket #202204. These components
should be hand tightened only. Over tightening of the filter
bowl will result in difficulty in removal at a later date. When
This filter will
assembly is complete, check for leaks.
When element absorbs its capacity of water (approximately
1/2 cup) the fuel flow will slow down. Keep a 496-5 element
on hand for replacement.
NOTE: This filter is rated for 150 psi pressure. If the fuel
system is prone to violent pressure surges (water hammers,
etc.), a pressure cushion device should be installed. A
vertical capped pipe installed in the line near the filter so
that it traps a pocket of air will serve this function. This is
not necessary unless pressure surges above 150 psi occur.
No. 491
Filter Bowl Wrench
• Fits bowl perfectly for
easy removal.
• Hangs on fuel tank.
(Ask your dealer.)
INSTRUCCIONES DE INSTALACION
Conectar la tapa superior del filtro a la válvula del
tanque de almacenamiento, en la abertura marcada "IN".
Asegurarse que la válvula de corte se encuentre entre el
filtro y el tanque. Conectar la manguera y la boquilla a la
abertura de filtro marcada "OUT". PRECAUCION: No apretar
la tapa del filtro apoyándose en el tazón del filtro. Colocar
la llave de tuercas en las superficies planas de la parte
central de la tapa del filtro para apretarla o quitarla. Ver la
ilustración.
Al instalar el elemento y el tazón, aplicar una capa de
aceite a ambos lados de la empaquetadura N° 202204.
Estos componentes deben apretarse a mano solamente. Si
se aprieta el tazón del filtro excesivamente, será difícil quitar
la caja en el futuro. Al terminar el armado, buscar fugas.
NOTA:
Este
Cuando el elemento absorbe su capacidad total de agua
filtro no absorbe
(aprox. 1/2 taza), el caudal de combustible se reducirá.
el agua de las
mezclas de
Tener un elemento 496-5 de repuesto a la mano.
combustible
NOTA: Este filtro tiene una capacidad nominal de presión
con alcohol.
de 150 psi. Si el sistema de combustible sufre variaciones
abruptas de presión (martillos hidráulicos, etc.), se debe
instalar un dispositivo amortiguador de presión. Un tubo
vertical tapado que se instala en la línea cerca del filtro de
modo que atrape una bolsa de aire cumple esta función.
Esto no es necesario a menos que se produzcan variaciones
transitorias de presión de más de 150 psi.
Llave para tazones de filtro
N° 491
• Se encaja en el tazón
para quitarlo.
• Pende del tanque de combustible.
(Solicitarla al concesionario.)
ACCESSORY ITEM
ACCESORIO ITEM

Publicité

loading

Sommaire des Matières pour Goldenrod Water-Block 496

  • Page 1 INSTALLATION INSTRUCTIONS IMPORTANT: Always mount Attach filter top cap to storage tank valve on opening cutoff valve between filter and tank! marked “IN”. Be sure there is a shutoff valve between filter and tank. Attach hose and nozzle to filter opening marked NO.
  • Page 2 INSTRUCTIONS D’INSTALLATION IMPORTANT: Toujours situer Raccordez le couvercle supérieur du filtre à la valve du la valve d’arrêt entre le filtre et le réservoir. réservoir de carburant à l’ouverture marquée «IN» (entrée). Assurez-vous qu’il y a une valve de fermeture entre le filtre NO.