Technical Assistance - Aube Technologies TI072 Guide De L'utilisateur

5.3 Configuration Menu
(Conf)
Use the Configuration menu to set the following parameters (see
sections 5.3.1 to 5.3.4).
5.3.1 Backlight mode (SCRN)
The screen is lit at high intensity for 8 seconds when you press any
button. The rest of the time, depending on the backlight mode
selected, the screen behaves as follows:
Scrn Off: The screen is not lit.
Scrn On HI: The screen is lit at high intensity.
Scrn On LO: The screen is lit at low intensity (default mode).
5.3.2 Automatic Daylight Savings Time Changeover (DLS)
When automatic daylight savings time changeover is on (DLS On), the
TI072 changes to daylight savings time (summer time) at 2:00 am on
the second Sunday of March and changes back to normal time (winter
time) at 2:00 am on the first Sunday of November. This function is
enabled (DLS On) by default.
5.3.3 Latitude and Longitude Coordinates (LAT and LONG)
The coordinates are used to turn the lights on at sunset and off at sun-
rise. The latitude is set to +45 and longitude to -75 by default. These
settings provide approximate sunset and sunrise times for most North
American cities. To obtain your city's coordinates (or those of a nearby
city), see the coordinates table. If your city is not listed, use a nearby
city or do a search for sites that provide latitude and longitude on the
Internet. The accuracy of the sunset and sunrise times depends on
the accuracy of the coordinates you enter for your city.
NOTE: Enter a negative value for a south latitude or a west longitude.
5.3.4 Correction Factor (ADJ)
If your city's time zone is based on political or economic boundaries
instead of its coordinates, your lights might switch on or off too early or
too late with respect to sunrise and sunset. In this case, apply a
correction factor (+1 or -1 hour; refer to addendum). Otherwise, leave
it at 0 (default value).
5.4 Program Menu
(Prog)
Use the Program menu to set the programs; i.e. the times you want
the lights to turn On or Off when the switch is in Automatic mode. To
set a program, proceed as follows:

Select a program number (see section 5.4.1)

Set the day(s) of the program (see section 5.4.2)

Set the program start time (see section 5.4.3)
5.4.1 Selecting a program number
You can set up to 21 "On" programs
("P01 On" to "P21 On") and 21 "Off"
programs ("P01 Off" to "P21 Off"). For
example, select an "On" program to set
when to turn the lights on; select an
"Off" program to set when to turn the
lights off.
5.4.2 Setting the day(s) of the program
After selecting a program, set the day(s) of the program. You can
select a specific day, all 7 days or "none". Choose "none" for any
unused program.
5.4.3 Setting the program start time
After setting the day(s) of the program, set its start time. You can
select either a specific time, the sunset time or the sunrise time:
• To select a specific time:
(1) Advance to the hour setting and select the hour.
(2) Advance to the minutes setting and select the minutes.
• To select sunset or sunrise time:
(1) Advance to the hour setting and select the sunset time or
sunrise time. (When you scroll, the sunset time
sunrise time appear between 11 pm and 12 am.)
(2) To enter an offset (from -70 to +70 minutes in 10-minute
increments) between the sunset or sunrise time and the
program start time, advance to the minutes setting and change
the minutes.
• EXAMPLE: If the sunset time is 6:13 pm and you change the
minutes to display 6:43 pm, you have entered a delay of 30
TI072
minutes. If, later in the year, the sunset time is 4:01 pm, the
program will start at 4:31 pm.
• NOTE: When you enter an offset,
or
remove the offset, display the sunset or sunrise time and
change the minutes until
5.4.4 Examples
Example 1: The lights turn on at sunset and off at 11:00 pm every day
(default setting).
Program
P01 On
P02 On to
P07 On
Example 2: The lights turn on at sunset and off at sunrise every day.
Program
P01 On
P02 On to
P07 On
Example 3: The lights turn on at 8:00 pm every day and turn off at
10:00 pm every day except on Saturday night when they turn off at
1:00 am.
Program
P01 On All 7 days
P02 On None
P03 On None
P04 On None
P05 On None
P06 On None
P07 On None
For example, if you set "P01 Off" at 10:00 pm for all 7 days and set
"P02 Off" to 11:00 pm for Saturday, on Saturday, the lights will turn off
at 10:00 pm, not 11:00 pm since "P01 Off" is set to an earlier time than
"P02 Off".

Keypad Lock
When the keypad is locked, the
only change permitted is the changing of the state. For example, if the
lights are off, they will turn on when you press the main button.
However, in Automatic mode, the default state for the current program
will be overridden until the next program starts. If you press the main
button again before the start of the next program, the lights return to
their initial state. To lock or unlock the keypad, press the buttons
in the following order:
"P01 On" "P01 Off"
NOTE: You must perform the whole procedure in an interval of 2
seconds. If the procedure was not properly performed, wait another 2
seconds before retrying.

Reset to default Settings
To return
simultaneously press both main and left buttons and
hold. The software version will appear for 5 seconds.
RST will appear for the next 5 seconds. Release the
buttons when all segments appear on the screen. The
and
switch is now reset (see default settings in the menu
flowchart).
appears along with
when you display the sunset or sunrise time. To
disappears.
Days Time Program Days
All 7 sunset P01 Off All 7
days days
None — P02 Off to None
P07 Off
Days Time Program Days
All 7 sunset P01 Off All 7
days days
None — P02 Off to None
P07 Off
Days Time Program Days
8:00 pm P01 Off Sunday (Su)
— P02 Off Monday (Mo)
— P03 Off Tuesday (Tu)
— P04 Off Wednesday (We)
— P05 Off Thursday (Th)
— P06 Off Friday (Fr)
— P07 Off Sunday (Su)
Be careful about overlapping!
icon appears on the screen and the
2 sec.
the switch to its default settings,

Troubleshooting
The display is faded or The ambient temperature is either below
irregular. or above switch's operating temperature.
The display disappears Swap the LINE and 3-WAY wires.
when you toggle the
other switch.
The sunset or sunrise • The date or time is wrong
time is inaccurate.
Time
• The longitude or latitude is wrong
11:00
pm
• The correction factor is wrong
—
• You have entered an offset

Specifications
Time
sunrise
Supply: 120 VAC, 60 Hz
—
Maximum load: 1800 watts
Operating temperature range: -15 °C to 50 °C (5 °F to 122 °F)
Storage temperature range: -40 °C to 60 °C (-40 °F to 140 °F)
Power outage: The screen is blank. Only the time must be set if the
outage lasts more than 4 hours; all other settings and programs are
permanently saved.
Time
Latitude range: from -65° to +65°
10:00 pm
Solar table precision: +/- 11 min. (within ±60° latitude)
10:00 pm
Certification: UL (c UL us)
10:00 pm

10:00 pm
Warranty
10:00 pm
10:00 pm
Resideo warrants this product, excluding battery, to be free from defects in workman-
1:00 am
ship or materials, under normal use and service, for a period of three (3) years from
the date of first purchase by the original purchaser. If at any time during the warranty
period the product is determined to be defective due to workmanship or materials,
Resideo shall repair or replace it (at Resideo's option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from
which you purchased it; or
(ii) call Resideo Customer Care at 1-800-831-2823. Customer Care will make the
determination whether the product should be returned to the following address:
6.
Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422, or
whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not
apply if it is shown by Resideo that the defect was caused by damage which occurred
while the product was in the possession of a consumer.
Resideo's sole responsibility shall be to repair or replace the product within the terms
stated above. RESIDEO SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF
ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WAR-
RANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON
THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, IS HEREBY LIMITED TO THE THREE YEAR DURATION OF THIS
WARRANTY. Some states do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which
vary from state to state. If you have any questions concerning this warranty, please
write Resideo Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-
800-831-2823.


Technical Assistance

7.
Tel.: 1-800-831-2823
For more information on our products, go to
www.resideo.com
8.
(see section 5.2).
(see section 5.3.3).
(see section 5.3.4).
(see section 5.4.3).
9.
10.
11.
2/4