Hella 2XD 980 911-701 Guide Rapide

Important Notes for
Installer and Owner
Introduction
This Multivolt LED lamp offers many advantages over conventional bulb lamps. Significantly reduced
power consumption, ultra long life and high tolerance to shock and vibration make this LED lamp the
ideal choice for industrial and commercial applications.
Electromagnetic Compatibility (EMC)
This LED lamp is an electronic device. The electrical circuits contain components that suppress
possible interference, both emission as well as susceptibility, to the limits prescribed in UNECE Vehicle
Regulation No. 10.
To avoid false signals or interference, it is standard practice that sensitive instrumentation such as
ABS and Tachometers etc. are provided with direct earths.
Protection against damage due to voltage spikes
This LED lamp is protected against damage from positive voltage spikes caused by events such as
load dump conditions up to severity level 3 of ISO 7637-2. The lamp is protected against reverse
polarity connection and negative voltage spikes of up to 1000 volts.
Electric Welding
Electric Welding may damage the LED lamps. For LED lamps, HELLA recommends the negative
connection to be wired isolated from the vehicle chassis. If the lamp uses the chassis as the earth
return it is recommended that this earth return is disconnected during electric welding.
Hot Surface Temperatures
Be careful when handling the lamp as the aluminium heat sink can reach temperatures over 65°C
depending upon the ambient temperature and the duration of operation. Please be careful not to cover
this surface as this could cause the lamp to overheat.
FIT AND FORGET - BY DESIGN
Congratulations!
The product you have selected comes from HELLA - a world leader in LED
lighting design.
Following the launch of the first LED automotive signal lamps in 1990, HELLA Design and Innovation continues
to set new standards. HELLA innovative solutions have been incorporated into millions of lamps, engineered and
tested to the most demanding standards, to suit the harshest environmental conditions.
The corner stone of the success of our products is our no compromise "Fit and Forget - by Design" philosophy
which is incorporated into every step of the product life cycle.
In a world consuming finite resources at an ever increasing rate, Fit and Forget – by Design is the right
environmental choice that also makes perfect economic sense to customers that consider the total life cycle Cost
of Ownership.
For general comments about Hella's products please contact us on E-mail at techfeedback@hella.co.nz
1
INSTRUCTION SHEET
Part No. 2XD 980 911-xx / 980911xx
for:
LED 360° Multi-flash Signal Warning Lamp
Housing Description: UV resistant Grilamid
Light source: Single LED
Operating Voltage: Multivolt 9-33V DC
Power Consumption: < 5W
Protective System: IP67
Mounting Instructions
The lamp should be mounted on a flat surface.
Drill three 5mm Ø mounting holes using the lamp
base as a template. The lamp has been designed to
use M5 bolts / screws (not supplied).
If passing the cable through a hole, ensure there
are no sharp edges to cut or chafe the cable.
Alternatively, cable can be routed through the sides
of the base. *
Connect lamp as per table below.
Try to keep the cable as long as possible, preferably
join the cable inside a sealed cable junction box.
* Requires a section of the base to be drilled /
broken out.
Wiring Colour Coding
The lamp is multivolt capable allowing full light output between 9 and 33 volts. LED modules are polarity
conscious. Reverse polarity will not damage this product but will inhibit its function. Hella recommends
wire connections be soldered, and heat shrink tubing applied to seal the joint.
Cable Colour Connect to
White Negative (-)
Red On (+)
Blue Flash (+)
Brown Sync
Note: Lamp must be protected by a fuse rated at 5 amperes maximum.
The On (red) cable is protected against large voltage spikes such as an alternator load dump. The Flash
(blue) and Sync (brown) cables may be permanently shorted to ground or to a maximum operating
voltage of 33 volts without damage to the circuit.
®
lens and ASA housing
General Dimensions (mm)
See Notes
90
Power Consumption
-
Less than 5 watts
Less than 5 watts
-
959 150-82 / 09.18