Cequent Performance Products 41939 Instructions D'installation

Bumper
Truck bracket
frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 41939F
Wrenches: 13/16, 7/8, 18mm, 21 mm, 22mm
Drill Bits: None
Figure 2
8
Qty. (2) Bolt-Hex, 9/16"-18 X 2" Gr5
1
Qty. (2) Block, 3/8" X 1-1/2" X 3"
2
3 Qty. (2) Block, 1/4" X 1-1/2" X 3", offset hole
Qty. (2) Flanged Locknut, 9/16-18
4
Qty. (2) Bolt-Metric, M14 X 2.00 X 45mm CL 10.9
5
Qty. (2) Washer-Lock 9/16"
6
Qty. (2) Block, 3/8" X 1-1/2" X 2"
7
1. Remove existing M14 bolts from bottom of each truck frame rail bumper bracket. Give bolts to customer.
2. Lift hitch into position, locating rearmost slots in hitch under existing weldnuts in truck frame.
3. Install new M14 bolts through lockwashers, blocks and hitch into weldnuts in truck frame.
4. Remove side M12 nuts and bolt plates at the end of the frame. Keep these for re-installation later.
5. If installing on a 2001-07 model, loosen the nuts at the bumper end of the bumper brace allowing it to swing away.
6. Place attachment bars as shown and loosely bolt to hitch. On the 01-07 models, swing brace back and fasten as shown.
7. Install remaining fasteners as shown through existing large holes in truck frame. Make sure to use thinner (1/4" x 3")
block below hitch and orient hole in block so that block lays flat against hitch when tightened.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009, 2010 Cequent Performance Products
Installation Instructions Installation Instructions
Bumper
2500HD / 3500 / 3500HD
Sierra & Silverado Trucks,
Classic & New Body - All
4
Existing bumper
b brace 2001-2007 2001 2007
only
Truck
frame
Attachment
Bar (provided)
Existing nuts
9 10 11 12
Note: All Fasteners Typical Both Sides of Vehicle
NOT ALL FASTENERS ARE USED
Tighten M14 CL10.9 fasteners with torque wrench to 100 Lb.-Ft. (136 N M) Tighten M14 CL10 9 fasteners with torque wrench to 100 Lb -Ft (136 N*M)
Tighten all 9/16" GR5 fasteners with torque wrench to 120 Lb.-Ft. (163 N*M)
Tighten M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
GMC & Chevrolet
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
1
2
3
NOTE: Install thinner
offset hole block here.
Orient hole as shown.
Existing bolt
5
6
7
plate
Figure 1
Qty. (6)
8
Qty.(10)
9
Qty. (4)
10
Qty. (2)
11
Qty. (6)
12
Qty. (2)
13
14 Qty. (2)
Sheet 1 of 3
Part Numbers:
41928
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Trailer WT
15,000 lb. (6810 Kg)
12,000 lb. (5448 Kg)
Wiring Access Location: PU3
Bumper
bracket
Existing weldnuts,
typical both sides
6 14
5 13 7
Bolt-Metric, M12 X 1.75 X 45mm CL 10.9
Washer, 1/2" Conical
Washer, 1/2" Flat
Lock washer, 1/2"
Nut, M12 X 1.75 CL 10.9
Washer, 9/16" Flat
Nut, M14 X 2.00
41939N 7-29-10
Form: F205 Rev A 5-6-05
41939
U-Haul
Max Tongue
WT
1500 lb. (681 Kg)
1200 lb. (545 Kg)
8
9
9
12
Figure 3
Vehicles without
bumper
Rev. B