Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Spare Tire
Muffler / Tail Pipe
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75678F
Wrenches: 18 mm
Drill Bits: none
Wire cable
Left mounting
bracket
Hitch receiver
1
Qty. (4)
Bolt – M12 x 1.75 x 45mm long CL 10.9
1.
Lower spare tire. See owners manual
2.
Pull wire loom retainer away from inside of right frame rail. See picture. Retainer will not be re-inserted.
3.
Lift hitch into place by placing the right mounting bracket between wire loom previously pulled away and the frame. Be aware this
is above the fuel fill lines. Lift left mounting bracket up into place, making sure to route wire cable thru large notch in side
is above the fuel fill lines Lift left mounting bracket up into place making sure to route wire cable thru large notch in side
bracket between mounting holes.
4.
Loosely install fasteners as shown.
5.
Pull hitch rearward and up so hitch receiver is level or above. Tighten fasteners.
6.
Raise spare tire back into place. Spare tire may rub against the right mounting of hitch when lifting. Check to see that the spare
tire is secure.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009 Cequent Performance Products
Installation Instructions
Wire cable
Ford Transit Connect
Wire cable routing
Tighten all M12 x 1.75 class 10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 n*m)
Ti ht
ll M12 1 75 l
Fascia
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
12
Right mounting
bracket
2
Qty. (4)
10 9 f t
ith t
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
4,000 (1816 Kg)
3,500 (1589 Kg)
Wiring Access Location: SUV 1, SUV2
g
Frame rail
Existing Weld nuts
Washer – 1/2" conical toothed
h t 92 Lb Ft (125 * )
75678N
9-28-09
Part Numbers:
75678
87570
44634
Max Tongue
WT (LB)
400 (182 Kg)
350 (159 Kg)
,
Wire loom retainer
Forward
Rev. B
Form: F205 Rev A 5-6-05
Publicité
Manuels Connexes pour Cequent Performance Products 75678
Sommaire des Matières pour Cequent Performance Products 75678
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75678N 9-28-09 Rev. B 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75678N 9-28-09 Rev. B 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Sheet 3 of 3 75678N 9-28-09 Rev. B 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...