Télécharger Imprimer la page

Imiola HAK-POL R/059 Instructions De Montage page 5

Publicité

• Odkręcić zderzak, lampy i belkę zderzeniową (nie będzie wykorzystana).
• Udrożnić technologiczne otwory i wsunąć do podłużnic elementy E i F.
• Przykręcić elementy C i D do podłużnic śrubami M12x40 (pkt 2, 3) oraz śrubami M10x 35 (4 i 5)
• Do elementów C i D przykręcić belkę zaczepu A śrubami M12x40 8.8 (pkt 1).
• Dokręcić wszystkie śruby z momentem wg tabeli.
• Założyć zderzak i lampy.
• Przykręcić kulę i blachę gniazda elektrycznego.
• Podłączyć instalację elektryczną.
• Unscrew the bumper, lamps and bumper bar (it will not be used any more).
• Clear the technological holes and insert the elements E and F in the frame side members.
• Screw the elements C and D to the frame side members with bolts M12s40 (point 2 and 3) and
with bolts M10x35 8.8 (point 4 and 5).
• Screw the main bar A to the elements C and D with bolts M12x40 8.8 (point 1).
• Tighten all the bolts according to the torque setting- see the table.
• Assemble the bumper and lamps.
• Fix the ball and electric plate.
• Connect the electric wires.
• Dévisser le pare-chocs, les lampes et la barre pare-chocs (non utilisée ultérieurement).
• Déboucher les trous technologiques et glisser les éléments E et F dans les longerons.
• Serrer les éléments C et D aux longerons à l'aide de boulons M12x40 (pts 2, 3) et de boulons M10x 35 (4 et 5)
• Serrer la barre d'attelage A aux éléments C et D à l'aide de boulons M12x40 8.8 (pt 1).
• Serrer tous les boulons avec un couple de serrage selon tableau.
• Installer le pare-chocs et les lampes.
• Visser le crochet d'attelage et socle de prise électrique.
• Raccorder le circuit électrique.
Die Rückleuchten, die Stoßstange und Verstärkung abschrauben.
ź
Die Gewindebohrungen in den Längsträgern säubern.
ź
Die AHK-Bauteile E und F mit Schrauben M10x35 8.8 (Punkt 4,5) an die Längsträger und mit Schrauben
ź
M12x40 8.8 an die Bauteile C und D (Punkt 2) anschrauben.
Den AHK-Querträger A an die Bauteile C und D mit Schrauben M12x40 8.8 anschrauben (Punkt 1).
ź
Ziehen Sie alle Schrauben mit dem Drehmoment gemäß der Tabelle an.
ź
Die elektrische Installation anschließen.
ź
Die AHK-Kugel und die Steckdosenplatte festziehen
ź
• Desenrosque el parachoques y la barra de impacto (ya no es necesario).
• Limpiar los oricios tecnológicos y insertar los elementos E y F a la largueros.
• Apretar los elementos C y D a la largueros con tornillos M10x35 8.8 (puntos 4, 5).
• Atornillar la viga de la bola de remolque A a los elementos C y D usando tornillos M12x40 8.8 (punto 1).
• Apretar todos los tornillos con el par según la tabla anterior.
• Montar el parachoques y las luces.
• Apretar la bola y la placa de la toma eléctrica.
• Conectar la instalación eléctrica.

Publicité

loading