Sauder Office Port 408365 Mode D'emploi
  1. Manuels
  2. Marques
  3. Sauder Manuels
  4. Ameublement d'intérieur
  5. Office Port 408365
  6. Mode d'emploi
Sauder Office Port 408365 Mode D'emploi

Sauder Office Port 408365 Mode D'emploi

Masquer les pouces
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
sauder.com
Library Base
Offi ce Port Collection | Model 408365
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
Get all organized
and stuff .
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-17
Français pg 18-20
Español pg 21-23
Lot # 387497
12/08/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicité

Table des Matières
loading

Manuels Connexes pour Sauder Office Port 408365

Sommaire des Matières pour Sauder Office Port 408365

  • Page 1 Offi ce Port Collection | Model 408365 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
  • Page 2 Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-17 Hammer Not actual size Français 18-20 Español 21-23 Skip the power trip. Safety 24-26 This time. Warranty Page 2 408365 www.sauder.com/services...

  • Page 3: Part Identifi Cation

    Use this part identifi cation to help identify similar parts. RIGHT END (1) LEFT END (1) TOP (1) BOTTOM (1) BACK (1) DOOR (2) ADJUSTABLE SHELF (1) SKIRT (1) BOTTOM MOLDING (1) TOP MOLDING (1) END MOLDING (2) www.sauder.com/services 408365 Page 3...

  • Page 4: Table Des Matières

    RUBBER SLEEVE - 4 GROMMET CAP - 1 BLACK 1/2" FLAT HEAD SCREW - 2 BLACK 9/16" LARGE HEAD SCREW - 20 BLACK 9/16" PAN HEAD SCREW - 2 BLACK 1" PAN HEAD SCREW - 4 Page 4 408365 www.sauder.com/services...
  • Page 5 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. To begin assembly, push a SAUDER TWIST-LOCK® å FASTENER (7F) into the large holes in the RIGHT END (A) and LEFT END (B).

  • Page 6: Twist-Lock Fastener

    Step 2 Fasten the BOTTOM (D) to the ENDS (A and B). Tighten å ® How to use the SAUDER TWIST-LOCK FASTENER four TWIST-LOCK® FASTENERS. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
  • Page 7 Step 3 Fasten the TOP (C) to the ENDS (A and B). Tighten four å TWIST-LOCK® FASTENERS. Some assembly (and snacks) required. These holes must be here. r f a w i t o l e www.sauder.com/services 408365 Page 7...
  • Page 8 Slide the END MOLDINGS (K) onto the notched edges of å the ENDS (A and B). * U.S. Patent No. 5,499,886 å Notched edge Notched edge Slide the END MOLDING (K) onto the notched edge. Slide the END MOLDING (K) onto the notched edge. Page 8 408365 www.sauder.com/services...

  • Page 9: Black 9/16" Large Head Screw

    NOTE: There are no pre-drilled holes in the TOP å MOLDING. The SCREWS will tighten into the groove. BLACK 9/16" LARGE HEAD SCREW (6 used in this step) These holes must be here. These surfaces should be even. www.sauder.com/services 408365 Page 9...

  • Page 10: Black 9/16" Pan Head Screw

    Fasten the MAGNETIC CATCH (1I) to the MAGNETIC CATCH å BRACKET (15I). Use two BLACK 9/16" PAN HEAD SCREWS (51S). BLACK 9/16" LARGE HEAD SCREW (2 used in this step) BLACK 9/16" PAN HEAD SCREW (2 used in this step) Page 10 408365 www.sauder.com/services...
  • Page 11 Step 7 Fasten the BOTTOM MOLDING (I) to the BOTTOM (D). å Tighten three TWIST-LOCK® FASTENERS. If you're doing this to help a friend, don't leave without a bite. Surface without holes www.sauder.com/services 408365 Page 11...
  • Page 12 NOTE: Be sure the BRACKETS are even with the edges of the ENDS. å Fasten the SKIRT (H) to the ENDS (A and B) and BOTTOM (D). Use å four BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (8 used in this step) Page 12 408365 www.sauder.com/services...
  • Page 13 Fasten the BACK (E) to your unit using the NAILS (1N). å NOTE: Perforations have been provided for access å through the BACK. Carefully cut out the holes needed. NAIL (17 used in this step) Cut-out www.sauder.com/services 408365 Page 13...

  • Page 14: Black 1/2" Flat Head Screw

    BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten a STRIKE PLATE (6I) to each DOOR (F). Use two å BLACK 1/2" FLAT HEAD SCREWS (11S). NOTE: The surface of the STRIKE PLATE with "SAUDER" å should be facing up. BLACK 9/16" LARGE HEAD SCREW (2 used for the PIVOT HINGES) BLACK 1/2"...
  • Page 15 Repeat this step for the other DOOR (F). å NOTE: To make adjustments to the DOOR, loosen the å SCREW in the HINGE, make needed adjustments, and tighten the SCREW. BLACK 9/16" LARGE HEAD SCREW (2 used for the PIVOT HINGES) www.sauder.com/services 408365 Page 15...

  • Page 16: Black 1" Pan Head Screw

    Fasten the PULLS (96K) to the DOORS (F). Use four å BLACK 1" PAN HEAD SCREWS (60S). Insert the GROMMET (38P) and GROMMET CAP (39P) å into the TOP (C). BLACK 1" PAN HEAD SCREW (4 used for the PULLS) Page 16 408365 www.sauder.com/services...
  • Page 17 NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. å And to celebrate, why not share your success story? 70 lbs. 25 lbs. 50 lbs. (4 used) www.sauder.com/services 408365 Page 17...

  • Page 18: Socle Pour Bibliothèque

    élément et conserver le livret pour future référence. EXTRÉMITÉ DROITE ..........1 FIXATION TWIST-LOCK® ........11 Pour contacter Sauder EXTRÉMITÉ GAUCHE ..........1 CONSOLE EN MÉTAL ..........4 en ce qui concerne cet DESSUS ................1 CONSOLE À ÉQUERRE .........3 élément, faire référence...
  • Page 19 éviter d’endommager l’élément ou le sol. Pour commencer l’ a ssemblage, enfoncer une FIXATION ÉTAPE 5 TWIST-LOCK® SAUDER (7F) dans les gros trous de l’EXTRÉMITÉ Fixer trois CONSOLES À ÉQUERRE (5G) au DESSUS (C). Utiliser DROITE (A) et l’EXTRÉMITÉ GAUCHE (B).
  • Page 20 REMARQUE : Les surface des PLAQUES DE BUTÉE comportant Ceci complète l’ a ssemblage. Pour nettoyer, utiliser l’encaustique l’inscription "SAUDER" devraient être dirigées vers le haut. pour meubles préférée ou un chiff on humide. Essuyer. Page 20 408365 www.sauder.com/services...

  • Page 21: Lista De Partes

    EXTREMO DERECHO ..........1 SUJETADOR TWIST-LOCK® .......11 et conserver le livret pour future référence. EXTREMO IZQUIERDO ..........1 SOPORTE DE METAL ..........4 Pour contacter Sauder PANEL SUPERIOR ............1 SOPORTE ANGULAR ..........3 en ce qui concerne cet FONDO .................1 15H BISAGRA DE PIVOTE ..........4 élément, faire référence...
  • Page 22 * Patente EE.UU. No. 5,499,886 Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (7F) dentro de los agujeros grandes del PASO 5 EXTREMO DERECHO (A) y del EXTREMO IZQUIERDO (B).
  • Page 23 Esto completa el ensamblaje. Limpie con su pulimento para NOTA: Las superfi cie de las PLACAS DE CONTACTO con la muebles preferido o un paño húmedo. Seque con un paño. inscripción "SAUDER" deben mirar hacia arriba. www.sauder.com/services 408365 Page 23...
  • Page 24 • This product is not designed to support a not designed to support a television is heavy. Plus the weight and location of the television. hazardous. picture tube tends to make TVs unbalanced and prone to tipping forward. Page 24 408365 www.sauder.com/services...
  • Page 25 Les téléviseurs peuvent être un téléviseur. cet eff et. particulièrement lourds. De plus, le poids et l’emplacement du tube image ont tendance à rendre les téléviseurs instables et enclins à tomber vers l’ a vant. www.sauder.com/services 408365 Page 25...
  • Page 26 Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y propensa a volcarse hacia adelante. Page 26 408365 www.sauder.com/services...

  • Page 27: Garantie Limitée De 5 Ans

    à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
  • Page 28 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.

Table des Matières