Lorelli VIOLA SET Mode D'emploi page 11

1. Install the front wheel by pressing them upward until they are locked. (Photo 5) Check for proper locking. For
dismounting press the button on the console and pull the wheel downwards. (Photo 6)
2. Assemble the rear wheels as shown in photo 7. For dismounting press the button on the rear axle and pull the
wheel. (Photo 8)
3. Install the carry-cot by taking care that the camps are placed and fixed in the designated holes of the chassis.
(Photo 11) Clicking means that the carry-cot is fixed. For disassembly, simultaneously press the side buttons of
the carry-cot and pull it upwards (Photo 12). The seat transformed into a carry-cot for a newborn must always
face the parent (photo 15).
4. Install the bumper bar for the child. (Photo 10) To remove the bumper bar, press the side buttons and pull it.
5. Fasten the zipper of the canopy to the carry-cot (Photo 9).
6. The carry-cot is transformed into a seat by fixing the belts located on the reverse part of the seat and the legs
(Photos 16/26). Carry-cot adjustment - Turn the carry-cot into a sitting position by pressing simultaneously the
side buttons. After positioning of the carry-cot (the seat), fix the hook against rocking (photo 17, 18)
Attention: Always release the hook before carry-cot adjustment.
Damage of the carry-cot adjustment mechanism due to incorrect operation is not covered by the
guarantee.
1. To fix the stroller in place, use the brake of the rear wheels by pressing backward the braking pedal located on
the rear axle. To release the brake, press the braking pedal forward (photo 31).
Attention! The brake does not guarantee optimal stopping on steep slopes! Therefore, do not leave the
stroller on a slope with a child that sits or lies in it! WARNING! The brake of your stroller is a kind of parking
device. To activate the brake, please note that the stroller shall not move. Carefully press the brake pedal and at
the same time mildly push the stroller forward-backward to synchronize the operation of the braking device and
for more secure activation of the braking mechanism.
2. You can adjust the handlebar by pressing simultaneously the two side buttons of the mechanism and turning
upwards or downwards.
3. When the stroller moves on rough and uneven surfaces, use the option for straightforward movement by
pressing the locking pin of the front wheels downwards (photo 21). To release the front wheels, raise the locking
pin.
4. To change the canopy position, hold the upper part and pull it down or up to the desired position (photo 13/14).
5. Backrest adjustment - to raise the backrest, press the button on the buckle behind the backrest and pull the
belt. To release the backrest, press the button of the buckle and release the backrest down (photo 19).
6. When using the seat, IT IS A MUST to place the safety belts for the child!
7. Attach the shoulder and the abdominal belts and fix them in the central buckle to lock them (photo 20). Adjust
the length of the safety belts by pulling the buckles (photo 21). To unlock the belts, push the button on the central
buckle (photo 22). For babies under 6 months, pass the belts through the straps (photo 23).
1. Activate the brakes of the stroller.
2. Stroller folding:
Variant 1 - if the seat is installed in the direction of movement (photo 26), the stroller is folded together
with the seat without dismounting it. Simultaneously push the big round side buttons of the seat and raise and
then fold the canopy as shown in photo 26. Press simultaneously the small round buttons and fold the lower part
of the seat upwards to the canopy as shown in photo 27. Pull the mechanisms from both sides of the handlebar
and push downwards (photo 28). The correctly folded stroller shall look like the one in photo 29. Lock the chassis
(photo 30).
Variant 2 - if the seat (carry-cot) is installed opposite the direction of movement, the stroller is folded
after dismounting the seat (the carry-cot) - photo 15. First, remove the seat (carry-cot) from the chassis via
the two semicircular side buttons located on both sides - photo 12. Then pull the mechanisms located on both
sides of the handlebar and push downwards until the chassis is fully folded. Lock the chassis (photo 30).
ASSEMBLING
EXPLOITATION
FOLDING
11