Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24797F
Wrenches: 10mm, 12mm, 13mm,
14mm, 17mm
Drill Bits: None
l
m
j
Qty. (2)
Hex Bolt M10 x 1.25 x 40mm CL8.8
k
Conical Washer 7/16"
Qty. (2)
1.
Lower exhaust by disconnecting muffler from rubber exhaust hangers, (3) places.
2.
Temporarily remove exhaust heat shield. Retain heat shield and fasteners for reinstallation after hitch is installed.
On driver's side, remove tie-down hook. Return tie-down hook and fasteners to vehicle owner.
3.
4.
Remove fasteners at end of frame rail as shown above and discard.
5.
Raise hitch into position and install fasteners into existing weldnuts as shown above.
6.
Reinstall heat shield.
7.
Raise exhaust back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2007, 2013, 2015 Cequent Performance Products, Inc – Printed in Mexico
Installation Instructions
Kia Rondo
Fascia
Drawbar Kit:
3594
(Sold separately)
Drawbar must be used in the
Rise position only.
Remove existing bolt
This location
Tighten all M8 CL8.8 fasteners to 20 lb.-ft. (27 N*M)
Tighten all M10 CL8.8 fasteners to 38 lb.-ft. (52 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg.) Max Tongue Weight
Existing weldnuts
In vehicle frame
l
j
m
k
l
Qty. (3)
Hex Bolt M8 x 1.25 x 30mm CL8.8
m
Conical Washer 3/8"
Qty. (3)
Sheet 1 of 3
Part Numbers:
24797
60874
77169
24915
Wiring Access Location: SUV1, SUV2
Remove existing bolt
This location
24797N
10-09-15
Form F206 Rev A 5605
U-Haul
Rev. C
Publicité
Manuels Connexes pour Cequent Performance Products 24797
Sommaire des Matières pour Cequent Performance Products 24797
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2007, 2013, 2015 Cequent Performance Products, Inc – Printed in Mexico Sheet 1 of 3...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systèmes d’attelage. z 2007, 2013, 2015 Cequent Performance Products, Inc - Imprimé au Mexique Feuille 2 de 3...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. Hoja 3 de 3 24797N 10-09-15 Rev. C 2007, 2013, 2015 Cequent Performance Products, Inc - Impreso en México Form F206 Rev A 5605...