Publicité
Les langues disponibles
Les langues disponibles
Connecting the cables
Depending on your printer configuration, the connector panel may
vary from the illustration.
1
2
3
4
5
1) DC power 2) cash drawer 3) USB 4) serial interface
5) AC power (Rating: 100-240V AC, 1.1A, 50-60 Hz)
Test print
1) Turn off the power switch on the printer.
2) Push the FEED button while turning on the printer.
Special Mode
1.Test Print
2.Setup Menu
3.Hex Dump
4.Command Trace
5.Sample Print
6.End
<Set>
Press FEED button for the number of times
as the same as your selecting item, and
wait more than 1 second.
3) Press the FEED button once
to start a test print.
Firmware Number
KA02041-Jxxx
Firmware Version 01A (0xxxxx)
123456
Memory Switch 1
Power On Status
Enable
Receive Buffer
4KByte
Busy Condition
Bufferfull
Receive Error
?Print
Auto LF
Disable
DSR(#6)Reset
Disable
INIT(#25)Reset
Disable
USB Soft Reset
Enable
Memory Switch 2
Cover Open Error
Auto Recovery
Error
Auto Recovery
Batch (COM IF)
Enable
Batch (Other IF)
Disable
Serial Number
Disable
ASB
Enable
Font-B
Mode1
Print
Paper Width
80mm/48columns
Max Speed
180mm/s
Print Density
100%
Hardware
Error Alert
None
Buzzer Interval
Pattern 2
Buzzer Repetition
Three
Graph/User NV-MEM
384KB/192KB
Cut at CoverClose
Disable
PNE Detect
Enable
Interface
Baudrate
115200BPS
Format
8NONE1
Protocol
DSR/DTR
USB
Printer
! " # $ % & ' ( ) * + , - . / 0 1 2 3 4
5 6 7 8 9 : ; < = > ? @ A B C D E F G H I
J K L M N O P Q R S T U V W X Y Z [ \ ] ^
_ ~ a b c d e f g h I j k l m n o p q r s
All manuals and user guides at all-guides.com
Safety instructions
Do not touch the printer's cutter and tear bar.
The print head is a thermal element and it is at high
temperature during printing or just after operation.
Therefore, do not touch it and its peripherals for
safety reasons.
The thermal head is an ESD-sensitive device. To
prevent damage, do not touch either its printing part
or connecting parts.
Caution:
•
The TH180 must be plugged into a grounded socket.
•
Always lay the supply leads and cables in such a way that
they cannot be stepped on or tripped over.
•
When setting up the appliance, ensure that the all
connecting devices and the grounded sockets are easily
accessible.
•
Check that the set nominal voltage of the appliance
corresponds to the local mains voltage.
•
In order to completely separate the appliance from the
mains voltage, switch off the appliance and disconnect it
from the mains.
•
In the event of an emergency (e.g. damaged housing,
damaged power supply cable, penetration of liquids or
foreign objects), immediately switch off the appliance and
disconnect it from the mains.
•
Switch off the appliance and disconnect it from the mains
before cleaning.
•
Install the printer on a flat and stable place.
•
Keep the printer away from water source.
•
Do not use or store the printer in a place exposed to heat
or fire, moisture, serious pollution and direct sunlight.
•
Do not place the printer on a place exposed to vibration or
impact.
•
No dew condensation is allowed to the printer. In case of
such condensation, do not turn on the power until
condensation completely disappeared.
•
Only use cables released by Wincor Nixdorf.
•
The printer should only be disassembled or repaired by a
technician who is certified by the manufacturer.
Further Information
Please find detailed information about the printer in the Operator's
Guide. That document as PDF file and needed drivers can be
downloaded from this web site:
http://www.wincor-
nixdorf.com/internet/site_EN/EN/Support/
Downloads/POSLotterySystems/poslottery
systems_node.html
Copyright© Wincor Nixdorf International GmbH, 2014
The reproduction, transmission or use of this document or its contents is not permitted
without express authority. Offenders will be liable for damages. All rights, including
rights created by patent grant or registration of a utility model or design, are reserved.
Delivery subject to availability; technical modifications possible.
Order No. 01750235803A
Wincor Nixdorf International GmbH
Wohlrabedamm 31
D-13629 Berlin
Publicité
