Westinghouse T26119 Mode D'emploi

All manuals and user guides at all-guides.com
Total Control Ground Stake
Wireless Remote Control
6 grounded outlets
Built-in darkness-sensing photocell
Countdown Mode: Turn devices on immediately for 2, 6 or 8 hours
Photocell Mode: Turn devices on at dusk for 2, 6, 8 hours or until dawn
Repeat function repeats set program daily
Transmitter works through walls, windows, and doors (80ft range)
Manual On/Off override button
LED indicators
Built-in overload protector
Command1 Expandable
Specifications:
6 Grounded outlets
125VAC/60Hz/15A/1875W Resistive
15A/1875W Tungsten
6ft 14/3 AWG SJTW Power Cord
433.92 MHz Frequency
INSTALLATION:
1. Select a location.
2. Do not set ground stake more than 5.5˝ inches into the ground. The outlets
should be as far from the ground as possible to prevent exposure in case of
flooding.
3. Plug the ground stake's cord into a 3-prong grounded elecrical outlet. (All
outdoor electrical devices should be plugged into a GFCI approved outlet.)
INSTRUCTIONS:
COUNTDOWN MODE:
Make sure the sliding mode switch on the transmitter is in the COUNTDOWN
position. Select from the following:
ON: Power will turn on instantly and stay ON until the device is powered OFF. The
[ON] indicator on the ground stake's front panel will illuminate.
OFF: Power will turn OFF instantly. All indicators on the ground stake's front panel
will turn OFF.
2HR, 6HR, 8HR: When pressed, power is ON instantly and will turn OFF after the
2 hour, 6 hour, or 8 hour selected countdown time. The corresponding 2HR, 6HR,
8HR indicators on the ground stake's front panel will illuminate. All indicators will
turn OFF after the program is completed.
Dusk/Dawn: When pressed, the unit will power ON at dusk and turn OFF at dawn
one time. The Dusk/Dawn indicator on the front panel will illuminate. All indicators
will turn off after program is completed.
Repeat Switch: When the sliding switch is in the Repeat On position the unit will
repeat the last 2HR, 6HR, 8HR, or Dusk/Dawn program daily. The power ON time
will be the same as the last set time. The unit will power OFF after the last selected
countdown time. The repeat indicator on the ground stake's front panel will
illuminate as well as the selected countdown time, until repeat mode is cancelled. To
cancel repeat mode, you must slide the repeat switch into the Repeat Off position
and press a desired function button. (Note: Sliding the repeat button without
pressing a corresponding function button will not initiate or cancel the repeat
function.
PHOTOCELL (DARKNESS-SENSING) MODE:
Make sure the sliding mode switch on the transmitter is in the photocell position.
Select from the following:
ON: Power will turn on instantly. The power will turn off at dawn automatically. The
[ON] indicator on the ground stake's front panel will illuminate.
OFF: Power will turn [OFF] instantly. All indicators on the ground stake's front panel
will turn off.
2HR, 6HR, 8HR: When pressed, power will be turned [ON] at dusk and off after
the 2 hour, 6 hour, or 8 hour selected countdown time. (Note: If dawn comes
before the selected countdown time has expired, the unit will turn off at dawn.) The
corresponding 2HR, 6HR, 8HR indicators on the ground stake's front panel will
illuminate. All indicators will turn off after the program is completed.
Repeat Switch: When the sliding switch is in the Repeat On position the unit will
repeat the last 2HR, 6HR, or 8HR program daily. The unit will power [ON] at dusk
and will power [OFF] after the last selected countdown time. The repeat indicator
on the front panel will illuminate as well as the selected countdown time until
repeat mode is cancelled. (Note: Sliding the repeat button without pressing a
corresponding function button will not initiate or cancel the repeat function.
MANUAL CONTROL
Press the ON button on the transmitter or the ON button on front panel of the
ground stake to override the current ON/OFF program status. If you press the OFF
button on the remote or press the ON button on the ground stake a second time, the
unit will revert back to the last programmed setting.
COMMAND1 TRANSMITTER PAIRING:
Note: Your Command1 Transmitter and Receiver contained in this package are
pre-programmed and ready to use. Command1 Pairing is only required for using
additional transmitters or if the channel has been changed on the transmitter.
This unit is equipped with patented Command 1 technology. All Westinghouse
indoor and outdoor transmitters have the ability to be paired with all Westinghouse
indoor and outdoor receivers. Please follow the directions below to pair a
transmitter to your receiver.
1. Locate the power [ON/OFF] button on the receiver.
2. Press and hold the power button for 3 seconds. The LED power indicator will
begin to flash slowly.
SAVE THESE INSTRUCTIONS!
Customer Service Assistance: Toll Free 1-855-350-6868
Hours of Operation – 10AM to 6PM, EST, Monday - Friday
WESTINGHOUSE and are trademarks of Westinghouse Electric Corporation. Used under license. All rights reserved.
Manufactured and distributed by: The NCC, Brooklyn, NY 11220 • www.thencc.com • © 2014 The NCC
POWER
COUNT
PHOTOCELL
DOWN
2HR DUSK/
DAWN
6HR 8HR
REPEAT
NOTE: If you are experiencing interference between 2 devices. Please, follow the
instructions below:
CHANNEL SELECTOR:
The back of your transmitter is equipped with a channel selector switch to
prevent interference between devices around your home. To prevent interruption
between 2 devices, set your transmitter to an alternate channel. Transmitter
channel codes are as follows: A, B, C, D.
Location: Peel off the sticker located above the word "channel" on the back of
the transmitter to expose the channel selector switch.
Be aware that every time a channel is changed Command1 Transmitter
Pairing is required. See Command1 Transmitter Pairing Instructions.
3. On your transmitter, press [ON] wait 2 seconds and then press [OFF]. The LED
indicator will now stop flashing.
4. You have successfully paired the transmitter to your receiver.
RESETTING THE UNIT
You can reset and remove all paired transmitters on your receiver by doing the
following:
1. Press and hold the [ON/OFF] button on the receiver for 3 seconds. The LED
indicator will begin to flash slowly. Continue to hold for an additional 3 seconds.
The LED indicator will now begin to flash rapidly. Release the [ON/OFF] button
for 1 second and press once again to confirm reset. The LED indicator should
now be OFF.
2. Your unit has now been reset and does not have any paired transmitters. (Note:
After reset, pairing is required to use the transmitter shipped in this package.)
BATTERY INFORMATION AND REPLACEMENT
The Remote Control uses a 3 volt CR2032 lithium battery. To replace, slide off the
battery at bottom side of the transmitter. Insert a new CR2032 lithium battery,
making sure to match up the + and – polarity markings. Slide the cover back in. To
test, press the ON or OFF buttons to make sure the LED lights up. Do not dispose of
batteries in fire. Batteries may explode or leak.
WARNING:
DO NOT splice, repair or modify. Unplug when not in use. Fully insert plug. DO
NOT use damaged remote sets. Inspect periodically. Use within the electrical
rating marked on the remote set. DO NOT plug more than a total of 1875 watts into
this remote ground stake. If watts are not marked on appliance, multiply ampere
rating (on nameplate) by 125 to determine equivalent watts. Add determined watts
for each plugged-in appliance or lamp (sum of watts on bulbs) to find total watts
being used. Operating temperature range –30ºC (-22ºF) to 45ºC (113ºF). Suitable
for damp locations. Not for water immersion or for use where directly exposed to
water. Store indoors when not in use.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
• Only use the batteries specified and be sure to match the + and - polarity
markings.
• Do not mix old batteries and new batteries or standard (carbon-zinc) with
alkaline batteries.
• Remove exhausted or dead batteries from the product.
• Remove batteries if product is not to be used for a long time.
• Do not dispose of batteries in fire. Batteries may explode or leak. As with all
small items, these batteries should be kept away from children. If swallowed,
seek medical attention immediately.
TROUBLESHOOTING TIPS
Problem Solution
The receiver Make sure the AC power cord is securely plugged into an AC
doesn't turn on power outlet.
Unplug the unit for a moment, and then plug it back in again.
Check the outlet by plugging in another device.
The remote Make sure the battery is fresh.
doesn't work
Stand closer to the receiver, the range should be up to 80ft.
Doors or walls will reduce the operational distance.
Item #T26119
28820
MANUAL
ON OFF
2HR 6HR
8HR DUSK/
DAWN
REPEAT REPEAT
ON OFF
COUNT PHOTOCELL
DOWN
Made in China