Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame
rail
Appearance
panel
Tie down bracket opening
on appearance panel
Hitch Shown In Proper Position
Equipment Required: 8" Ratchet Extension
Fastener Kit: 24860F
Wrenches: 10mm, 17mm, 19mm
1/2" / 13 mm
4" / 102 mm
Heat Shield
j
Qty. (4)
Hex bolt M12 X 1.25 X 35 CL8.8
Remove the tie-down hook on driver's side. Note: remove the bolts leaving the appearance panel in
1.
place. Return tie-down hook and fasteners to vehicle owner.
2.
Lower exhaust at (2) hangers, (1) at front and (1) at rear of muffler. Note: Spraying a lubricant or soapy
water on the metal hanger rod and the rubber isolator helps removal. Be careful not to allow muffler to
fall under its own weight.
3.
Temporarily remove exhaust heat shield. Use a marker or tape to mark heat shield for trimming and
confirm the trim. Trim heat shield and reattach.
Raise the driver's side of the hitch into position through the tie-down bracket opening. With the
4.
passengers side on the ground rotate the hitch through the cut-out. Leave hitch supported (jack, blocks,
nd
2
person).
5.
Raise the passengers side of the hitch over the tail pipe, sandwiching heat shield between the frame and
bracket. Gently bend heat shield back into position. Loosely install fasteners.
6.
Install remaining fasteners as shown.
7.
Tighten all fasteners to the required torque specification.
8.
Reinstall exhaust.
Tighten all M12 CL8.8 fasteners with torque wrench to 65 Lb.-Ft. (88 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010, 2012, 2015 Cequent Performance Products - Printed in Mexico
Installation Instructions
Fascia
(Sold separately)
Drawbar Kit:
Drawbar must be used in the
Rise position only.
Tie down
bracket opening
Appearance panel shown
off vehicle
3" / 77 mm
Note: Fasteners typical both sides
Lexus HS 250h
3594
Frame
rail
Tie down hook
Appearance panel not shown
installation view for clarity
k
Conical washer 1/2"
Qty. (4)
Sheet 1 of 3
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location:
Heat shield not
shown installation
view for clarity
k
j
24860N
10-07-15
24860
60276
77237
Rev. C
Publicité
Manuels Connexes pour Cequent Performance Products 24860
Sommaire des Matières pour Cequent Performance Products 24860
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24860N 10-07-15 Rev. C 2010, 2012, 2015 Cequent Performance Products - Printed in Mexico...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. de l’état de New York concernant les spécifications en matière de sé curité des systè mes et dispositifs d’attelage. z 2010, 2012, 2015 Cequent Performance Products - Imprimé au Mexique Feuillet 2 sur 3...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. Hoja 3 de 3 24860N 10-07-15 Rev. C 2010, 2012, 2015 Cequent Performance Products - Impreso en México...