Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75692F
Wrenches: ¾, 19mm
Drill Bits: None
Hitch crosstube
Gently pull down and rearward at fascia attachment for
additional clearance if needed at crosstube.
Do Not distort Fascia
1
Qty. (2)
Hex bolt ½-13 x 1.75 GR5
2
Qty. (4)
½ Conical Toothed Washer
1.
Raise hitch into position and align the slots of the receiver with the weldnuts in the frame rail.
2.
Install the M12 X 1.25 X 40mm bolts and conical toothed washer through the hitch and into the weldnuts.
3.
Insert the handle nuts through the large hole in the vehicle frame rail as shown above.
4.
Install the ½-13 X 1.75 bolts and conical toothed washers.
Tighten all M12 X 1.25 CL 10.9 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)
Tighten all M12 X 1 25 CL 10 9 fasteners with torque wrench to 115 Lb Ft (156 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010 Cequent Performance Products
Installation Instructions
Fascia
Frame Rail
Fascia attachment
bracket
Bottom of
Fascia
Tighten all 1/2-13 GR 5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Acura RDX
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
4
4
Wiring Access Location: SUV1, 2
3
Qty. (2)
4
Qty. (2)
Sheet 1 of 3
Max Gross
Trailer WT (LB)
Not For Use With Spring Bars
4000 (1816 Kg)
Note: Fasteners typical
both sides
Existing Weldnut
– Both Sides
2
3
M12 X 1.25 X 40mm CL 10.9
½ Handle Nut
75692N
12-8-10
Part Numbers:
75692
87584
44646
75190
U-Haul
Max Tongue
WT (LB)
400 (182 Kg)
4
2
1
Rev. C
Form: F205 Rev A 5-6-05
Publicité
Manuels Connexes pour Cequent Performance Products 75692
Sommaire des Matières pour Cequent Performance Products 75692
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75692N 12-8-10 Rev. C 2010 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75692N 12-8-10 Rev. C 2010 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 75692N 12-8-10 Rev. C 2010 Cequent Performance Products Form: F205 Rev A 5-6-05...