Technical Data - Niko 352-08440 Mode D'emploi

352-08440 / 352-08441 / 352-08442 / 352-08455 / 352-08456 / 352-08457
Read the complete manual before carrying out the installation and activating the system. Keep the
manual for future reference.
1. DESCRIPTION
This is an adaptable and energy-efficient LED spot with a clean design. The spot is suitable for outdoor use.
With its homogeneous lighting effect, the spot ensures superior lighting in all conditions.
This manual applies to the following spots:
reference colour
352-08440 white
352-08441 black
352-08442 alu
352-08455 white
352-08456 black
352-08457 alu
This spot is also available with a built-in PIR sensor (see reference numbers 352-0132x and 352-0133x).
2. USE
This spot is suitable for wall mounting outdoors. Keep a safe distance of 20 cm from the ceiling (30 cm when
mounting in an internal corner).
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire shall be replaced.
3. MOUNTING
1. Choose the mounting site for the spot. Drill the hole for the screw carrying the spot, located in the middle
on top of the spot. Press the included plug into the drill hole and insert the included screw into the plug.
2. Turn the head of the spot 180° into the service position (see fig. 1a).
3. Unscrew the screw at the bottom of the device and slide the cover downward (see Fig. 1b).
4. Hook the device over the mounted screw (see Fig. 1c). If you're happy with the spot's position, draw two
drilling holes on the wall for the two others screws (see Fig. 1d). Unhook the device from the wall, drill the
holes and insert the included plugs into the holes.
5. Insert the power supply cable through the cable inlet at the back of the spot (see Fig. 1e).
6. Place the device over the middle screw and insert the two included screws into the plugs (see Fig. 1d).
7. Connect the wires as shown in the wiring diagram (see fig. 2 and § 4).
8. Slide the cover back up.
9. Reverse the head of the spot with 180° (operating position).
The head of the spot can be rotated 10°, both horizontally and vertically. Never deviate the head more than 4° from
the horizontal axis to prevent heat concentration on one side. The spot may not be turned on in service position.
4. WIRING
Connect the detector as shown in the wiring diagram in fig. 2.
Conductor
Neutral conductor
Earthing
5. TROUBLESHOOTING
Malfunction Solution
The switch output does not switch. • Check the lighting and the fuse.

6. TECHNICAL DATA

Reference
Dimensions in mm
Lampshade material
Lamp type
Nominal power
Nominal voltage
Power factor
Light intensity
Light efficiency
Colour temperature
Protection class
Protection degree
Ambient temperature
Marking
4
EN nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
nominal power
15 W
30 W
L
N L
N
L' L N
352 - 08440 / 352-08441 / 352 - 08455 / 352-08456 /
352-08442 352-08457
170 x 292 x 212
metal/plastic
COB LED
15 W
230 – 240 V, 50/60 Hz
> 0,6
1000 lm 2000 lm
67 lm/W
4000 K
Protection class II
IP55
-20 – 40 °C
CE marked
7. WARNINGS REGARDING INSTALLATION
• The installation should be carried out by a registered installer and in compliance with the statutory regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file,
and it should be passed on to any new owners. Additional copies are available on the Niko website or via
the Niko support service.
• During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope
of each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EU declaration of conformity regarding this product at www.niko.eu.
8. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.
9. GUARANTEE PROVISIONS
• The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of
purchase of the product by the consumer. If there is no invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity, within two months after
stating the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point. Together with producers
and importers, you have an important role to play in the advancement of sorting, recycling and reusing discarded electrical
and electronic appliances. In order to finance the waste collection and processing, the government levies a recycling
contribution in some cases (included in the purchase price of this product).
30 W
PM352-08440R16322