Armacost Lighting Proline 780001 Guide Rapide

Proline RGB+White LED Amplifier
Use LED amplifiers throughout larger lighting designs with a single
■
color controller to maintain color consistency and synchronization
of any color-changing effect.
Use in conjunction with a color controller and an auxiliary power
■
supply for large perimeter and array lighting applications.
Connect multiple LED amplifiers to a single RGB+W controller to
■
color control limitless lengths of RGB+W lighting.
Connections and Typical Applications
In large area applications the low voltage wire that runs from the RGB+W color controller to the LED lighting can sometimes be too long to carry
adequate power due to voltage drop. By integrating one or more RGB+W LED amplifiers into the lighting installation, you can repeat the RGB+W
signal from the color controller to add RGB+W lighting to other areas.
IMPORTANT: This device amplifies or repeats the RGB+W signal, not the power. Each LED amplifier installed will require a separate power supply.
Output rating (watts) of the power supply connected to the LED amplifier is dependent on the power requirements of the LED lighting that is connected
to the LED amplifier. Follow your RGB+W LED tape model instructions to determine power supply requirements.
Power Supply Input
Follow your RGB+W LED tape
model instructions to determine
power supply requirements
RGB+W Signal Input
Status Indicator
Steady green: Normal working mode
Yellow flash: Overheat protection
Red flash: Overload/short circuit protection
When a color controller is wired directly to one or more RGB+W LED amplifiers (not connected to RGB+W LED lighting), the LED amplifiers and
LED lighting can be located up to one hundred feet from the actual color controller. This can often solve voltage drop issues and may also help
with certain installation needs. When a controller is direct wired to a LED amplifier, the cable will be transmitting only data, so a thick cable is not
needed. Armacost Lighting 5C 22AWG Ribbon Flat Cable is recommended.
Perimeter Lighting Application
Color
Controller
Power
Supply
120V AC
Input
RGB+W tape light length limitation is based
on your model of RGB+W LED lighting
Safety Protection
The amplifier has a function to prevent it from being damaged by mis-
wiring, output short circuit, overloading, or overheating. It will automatically
shut down under these extreme conditions until safe operating conditions
are restored. To avoid shutdowns, make sure the installed LED lighting
is compatible with constant voltage driving, is in the rated range of the
amplifier, and the cables are well connected and insulated. Also, install
the amplifier with proper ventilation and heat dissipation in mind.
SPECIFICATIONS
Working voltage ......................DC5–24
Rated output current ... 4x8A (24A max)
Standby current ....................... <15mA
Signal voltage range ...Power voltage ±3V
Time shift .................................< 5uS
Output mode ...... PWM constant voltage
Output to RGB+W Lighting
5-conductor cable can be thin, i.e. 22AWG
LED
Amplifier
Overload protection ........................Yes
Overheat protection ........................Yes
Working temperature ........ -4° – 131 °F
..................................... (-20° – 55°C)
Dimensions ........ 5.28 x 1.54 x 0.93 in.
.......................... (134 x 39 x 23.5mm)
Professional-grade, high-capacity unit is rated for up to 288 watts
■
of 12-volt RGB+W LED tape lighting or 576 watts of 24-volt LED
lighting. No minimum load is required.
Suitable for indoor or outdoor use when unit is installed in a proper
■
wet location enclosure.
Uses proprietary high speed optocouplers that keep LED lighting
■
colors and effects in synchronization regardless of the number of
LED amplifiers installed.
120V AC
Input
Power
Supply
Color
Controller
Connect inline
to color control
limitless lengths
of RGB+W lighting
Large Array
Remote
Installation
Application
120V AC
Power
Supply
Controller
When a color
controller is direct
wired to the RGB+W
LED amplifier, the
color controller
can be up to one
hundred feet from
the LED amplifier
and the lighting
Manufactured in China
armacostlighting.com
© 2020 Armacost Lighting. All rights reserved.
Power
Supply
LED
Amplifier
LED
Amplifier
Power
Supply
Power
Supply
LED
Amplifier
Input
Power Power
Supply Supply
Color LED
Amplifier
Power
Supply
LED
Amplifier
AL Item # 780001
Power
Supply
LED
Amplifier
LED
Amplifier
Power
Supply
201001