Publicité
Les langues disponibles
Les langues disponibles
- TIMER: The hood is equipped with a device for automatic stop after 5 (or 10) minutes. To activate this function, see
point 4 of the instructions.
- CLOCK: the time can be shown on the display. To activate this function or set the time, see point 5 of the instructions.
- SENSOR SENSITIVITY: You can adjust the sensitivity of the sensor according to your specific needs. To access
this function, see point 6 of the instructions.
- INSIDE TEMPERATURE INDICATION: The inside temperature of the room can be shown on the display. To activate
this function, see point 7 of the instructions.
- OUTSIDE TEMPERATURE INDICATION (optional): It is possible to have the outside temperature shown on the display.
To activate this function, see point 8 of the instructions.
- GREASE FILTER CLEANING INDICATION: The hood signals when it is time to clean the grease filters. See point 9
of the instructions.
- CHARCOAL FILTER REPLACEMENT INDICATION: The hood signals when it is time to replace the charcoal filters (for
appliances in the filtering version). See point 10 of the instructions.
1. Key "A" (ASC function) : To activate the sensor function, press key "A". With the sensor activated, the hood switches
on automatically in the presence of any type of odour, steam, smoke, or heat from the cooking process, and also in the
presence of any anomalous gas leaks in the environment. When the sensor is active, the display shows the symbol
To disactivate the sensor, press the key A. With the sensor activated, pressing the - key or the + key takes you directly
to the manual function and the symbol
2. Key
: Light On/Off.
3. Minute counter: To activate the counter, press the "MENU" key (the symbol
"ok". The display shows the number 00.00 blinking. Using the - and + keys you can set the desired number of minutes
(from 1 to 99); keeping the - or + key pressed, the number of minutes scrolls rapidly. Press "ok" to confirm, then press
"MENU" to exit. When the minutes have elapsed, an ACOUSTIC SIGNAL is emitted and the indication blinks on the display:
press "ok" to disactivate it (otherwise, it is disactivated automatically after 5 minutes).
To disactivate the counter at any moment, press the "MENU" and "ok" (reset) keys together.
4. Timer: When the timer is activated, the hood stops automatically after 5 minutes (or 10). To activate the timer, press
the "MENU" key and then the - and + keys until the blinking symbol
You can select the timer for 5 or 10 minutes by pressing the - and + keys, and then press "ok" to confirm. To exit from
the menu, press the "MENU" key.
5. Clock: To activate the clock function and set the time, press the "MENU" key and then the - and + keys until the 4
digits appear on the display blinking; set the time using the - and + keys, then confirm with "ok". To exit from the menu,
press the "MENU" key. To disactivate the clock function, press the "MENU" and "ok" (reset) keys together.
6. Sensor sensitivity: To adjust the sensitivity of the sensor, press the "MENU" key and then the - and + keys until the
symbol
blinks on the display. Then press "ok", select the sensitivity from 1 to 9 using the - and + keys and confirm
with "ok". To exit from the menu, press the "MENU" key".
7. Inside temperature indication: To view the inside temperature on the display, press the "MENU" key and then the - key
(or + key) until the display shows "In 18°C" or similar; then press "ok". The inside temperature is measured by a measuring
device (included) which can be positioned anywhere in the room.
8. Outside temperature indication (optional): To view the outside temperature on the display, press the "MENU" key and
then the - key (or + key) until the display shows "Out 15°C" or similar; then press "ok". The outside temperature is measured
by a measuring device (optional) that can be positioned outside the building, protected from water (maximum distance
on a direct line: about 15 m).
9. Grease filter alarm: After approximately 30 hours of operation, the display will show the symbol
is time to clean the grease filters. Once the filters have been cleaned, restart the hour count by pressing the "MENU"
and "ok" (reset) keys at the same time.
10. Charcoal filter alarm: After approximately 120 hours of operation, the display will show the symbol
it is time to replace the charcoal filters. Once the filters have been replaced, restart the hour count by pressing the "MENU"
and "ok" (reset) keys at the same time.
LIST OF SYMBOLS
SPEED (4 speeds + extra-high speed)
AUTOMATIC SENSOR
19.38
CLOCK
MINUTE COUNTER
is shown.
appears on the display), then press
appears on the display; confirm by pressing "ok".
.
, indicating that it
, indicating that
Publicité
