Knape & Vogt PDN22ST-W Instructions D'installation

Parts Included
A. (2) or (5) shelves
B. Telescopic Post
C. (2) Universal Mounting Plates
D. (2) or (5) Bearing Hubs
E. (3) or (6) Bearing Pins
F. (8) #8x1/2" screws
G. (2) or (5) Shelf Retention Clips
H. (1) Care and Cleaning Sheet
C
B
D
A
E
G
F
Tools Required
• Phillips head Screwdriver
• Drill with 1/16" (1.5mm) bit for
drilling pilot holes
• Tape measure or ruler
• Pencil
Product Assemblies
PDN22ST-W
PDN22S5T-W
KNAPE & VOGT MANUFACTURING COMPANY
P.O. Box 191, Muncie, IN 47308
0.899.6535 • 765.288.8730 • Fax 765.288.0851 • www.kv.com
D-SHAPE POLYMER LAZY SUSAN
Installation Instructions
Inspect all parts and read all instructions prior to beginning assembly and installation.
Step 1 Use installation template to mark and drill 1/16˝ pilot
holes for Universal Mounting Plates (C) in top and bottom interior of
cabinet.
Step 2 Fasten each of the Universal Mounting Plates (C) with (2)
#8 x 1/2˝ Screws (F) using the slots so that future adjustment can be
made, if necessary.
Step 3 Insert Bearing Hubs (D) into the underside of each of the
Shelves (A). Note that the keyway on the side of the Bearing Hub
must be aligned with the key on the inside of the Shelf.
Step 4 Slide all of the Shelves onto the lower portion of the
Telescopic Post (B) from the bottom (slotted side).
Step 5 Place the assembly into the cabinet. Align the bottom of the
Telescopic Post over the top of the bottom Universal Mounting Plate
making sure that the slot in the Post fits over the lug in the Mounting
Plate and faces towards the front. Push a Bearing Pin (E) through the
slot in the pole and the hole in the Mounting Plate. Slide the Bottom
Shelf down onto the pin.
Step 6 Loosen the set screw that holds the upper portion of the
Telescopic Post enough to allow the upper portion to move. Slide the
upper portion up onto the top Universal Mounting Plate so that it is
engaged securely. Tighten the setscrew to hold the upper and lower
portions of the post together securely.
Step 7 Starting with the top shelf, temporarily raise the shelf to the
top of the pole above the last set of shelf positioning holes and push a
bearing bin (E) through the pole at desired location. Lower shelf onto
pin. Repeat this process with the remaining shelves.
Step 8 To ensure the shelves remain in place during cabinet
shipment, attach the shelf retention clip into the posthole directly
above each shelf. If cabinet is already installed, the shelf clips are
not needed and may be discarded.
Step 9 Check the alignment of the Shelves with the cabinet
door opening by rotating the Shelves so that the detents (notches)
on the Bearing Hubs engage the Bearing Pins to stop the Shelves.
If the Universal Mounting Plates were installed correctly using the
template, the Shelves should be perfectly aligned with the cabinet
door opening. Should additional adjustment be needed, loosen the
Screws holding the Mounting Plates just enough to allow rotation
of the entire unit. Rotate the unit until the Shelves are in alignment
with the cabinet opening, and tighten the Screws. Add remaining
#8 x 1/2˝ Screws to the round holes in the Mounting Plates to
complete the installation.
Installation is complete! Affix the enclosed "Care Instructions" to an
inside wall of the cabinet for future reference.
1 & 2
3
4
5, 6 & 7
9
RN-246EFS 05/03