Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
2003-08 Fascia
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24913F
Wrenches: 17mm, 19mm
For vehicles with appearance
panel:
Remove appearance panel which
covers the trunk pan.
(2)10mm
Remove the plastic rivets that
fasten the fascia tabs to the
vehicle. Note: Remove the center
of the rivet with a screwdriver.
Rivets to be reinstalled.
Return appearance panel and
fasteners to vehicle owner.
j
Qty. (4)
Hex Bolt, M12 X 1.25 X 35 CL8.8
If present, remove the tie down brackets from vehicle frame rail. Return bolts and tie down bracket to owner.
1.
Raise hitch into position and install fasteners as shown above.
2.
Tighten all fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Tighten all M12 CL8.8 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2013, 2015 Cequent Performance Products
Printed in Mexico
Installation Instructions
Toyota Corolla
2009 Fascia
2014 Fascia
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in
the RISE position only.
Note: Fasteners typical
both sides
Frame rails
Existing weldnuts
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
k
Qty. (4)
Conical washer
Sheet 1 of 3
24913N
Part Numbers:
24913
60345
77300
Manufacturer's Rating or
Wiring Access Location: PC3, 4
k
j
10-05-15
Form F206 Rev A 5605
Rev. B
Publicité
Manuels Connexes pour Cequent Performance Products 24913
Sommaire des Matières pour Cequent Performance Products 24913
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24913N 10-05-15 Rev. B 2013, 2015 Cequent Performance Products Printed in Mexico Form F206 Rev A 5605...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systè mes d’attelage. Feuille 2 de 3 24913N 10-05-15 Rev. B 2013, 2015 Cequent Performance Products Imprimé au Mexique Form: F205 Rev A 5-6-05...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulació n V-5 y SAE J684 2013, 2015 Cequent Performance Products Hoja 3 de 3 24913N 10-05-15 Rev.