Attwood Matrix Instructions D'installation

3
Matrix ™
Marine Seating
Installation Instructions
SAVE THESE INSTRUCTIONS
Form Number 69416 Rev. A
SEAT FEATURES
The Attwood Matrix™ Marine Seat offers advanced ergonomic contouring.
Some models offer shock-absorbing elastomeric mesh in the Seat Pan.
The seat meets Type A Driver ABYC H-31 regulations for driver's
seat applications. Installers and users should abide by all ABYC
and U.S. Coast Guard regulations for seating.
COMPONENTS INCLUDED:
Before beginning, be sure you have these components:
• Seat Core
• Seat Pan
• Blank Back Panel
You may also have these optional components:
• Seat Bolster
• Warning Label for Bolster
• Arms (Left & Right) or Headrest
• Cargo Panel Assembly with Trim Ring
REQUIRED FOR INSTALLATION
Component Fastener
Arms, 1/4" dia. plastic thread forming screw,
Left & Right (hi/low), stainless steel, 2" (51mm) long.
1/4" dia. plastic thread forming screw,
Headrest (hi/low), stainless steel, 2" (51mm) long.
1/4" dia. plastic thread forming screw,
Cargo Panel (hi/low), stainless steel, 1" (26mm) long.
1/4-20 stainless steel screws.
Seat Pedestal Typical length is 1-1/4" (31mm).
UPHOLSTER CORE AND COMPONENTS
1. For seats specified WITHOUT Cargo Panel:
• Apply spray adhesive to inside of blank back panel, then press
into cavity in back of seat. Upholster over this back panel.
2. Attach foam and upholster these separate components:
• Seat Core
• Seat Bolster
• SAS Seat Pan
• Arms (Left & Right) or Headrest
3. Sew the Warning Label onto front of Seat Pan after it has been
upholstered. The Label will not be visible when Bolster is down.
(Figure 1)
Figure 1
®
Warning Label
NOTE: While the Bolster does qualify as a Type A Seat under
ABYC Standard H-31, Attwood strongly suggests that you install
the Warning Label that warns against use over 5 mph. The Label
also warns against potential pinch points and dangerous use.
ASSEMBLE COMPONENTS
Attach Optional Arms (Left & Right)
1. Find 4 locator holes in the Seat Core, beneath the upholstery:
(Figure 2)
• 2 vertical, one at each side
• 2 horizontal, one at each side
2. Staple upholstery to hold it to the core around the holes.
3. Carefully cut a slit in the upholstery to match size of each hole.
4. Hold Left Arm with hook at top. Insert hook into vertical hole, then
roll down so post fits into horizontal hole.
06-02
5. Working from interior of the seat, find the screw dimple above the
Bolster opening in the core.
6. Insert a plastic thread forming screw (2"-long x 1/4" dia.)
horizontally through the screw dimple and drive it into post
at the base of the Left Arm.
CAUTION: To avoid stripping the thread, DO NOT exceed
40 in./lbs of torque.
7. Repeat procedure with opposite Arm.
Figure 2
NOTE: Staple Upholstery
BEFORE Cutting Holes
Vertical Hole
Qty.
2
3
6
Attach Optional Headrest
4
1. Find 3 locator holes in the Seat Core, beneath the upholstery: (Figure 3)
• 1 top hole
• 2 horizontal holes, one at each side
Figure 3
Hook
Screw Through Dimple
Horizontally into Arm Post.
40 in/lbs. MAX
Post into Horizontal Hole
Do Not Staple In This Area
Until Screw Has Been Installed
Tab into Top Hole
Staple Upholstery Before Cutting Holes
Screw Through Dimple
Horizontally into Arm Post.
40 in/lbs. MAX
Post into Horizontal Hole
Do Not Staple In This Area
Until Screw Has Been Installed