Inovonics EchoStream EE4000 Instructions D'installation

EE4000/EE4200 EchoStream
Installation Instructions - 04598B
Overview
The serial receiver is a gateway that uses reliable frequency-hopping, spread-spectrum
technology to decode radio frequency (RF) transmissions from end devices and high-power
repeaters, then outputs the decoded data to the application controller in a common serial
data format.
Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics technical support:
• E-mail: support@inovonics.com
• Phone: (303) 939-9336
Connect the Serial Cable
Caution: Long cable runs should not be adjacent to high current power feeds. Keep cable
lengths as short as possible to minimize noise pickup. Measure voltage at the serial receiver
on long cable runs.
1. Use a small screwdriver to press the housing release tab (Fig. 1A); separate the housing.
2. Connect a serial cable to either the serial data port (Fig. 1B) or the serial data terminal
(Fig. 1C). Cabling should meet the following specifications:
4-conductor 20AWG (or larger) stranded-tinned copper with PVC
Cable requirements
insulation rated to 300 volts at 26°C (80°F). (Belden #8205, for example.)
15.25 meters (50 feet).
Maximum cable length
3. Route the cabling through either the bottom cabling knockout (Fig. 1D) or the side
cabling knockout (Fig. 1E).
Mount the Serial Receiver
Caution: Mount the serial receiver in a location removed from metal. Metal objects (duct
work, wire mesh screens, boxes) will reduce RF range.
1. Use the provided anchors and screws to mount the serial receiver in a location accessible
for future maintenance.
2. Close the serial receiver housing.
Serial Receiver Operation
Caution: The EchoStream system should be tested regularly to ensure operation. To test,
place the system in test mode, activate an end device, and ensure an appropriate response.
The following LEDs are used to monitor serial receiver operation:
Lit when the serial receiver is transmitting data to the application controller
Transmit LED
(Fig. 1F).
Lit when the serial receiver is receiving data from the application controller
Receive LED
(Fig. 1G).
Lit when the serial receiver is decoding an RF transmission from another
Decode LED
Inovonics Wireless device (Fig. 1H).
Specifications
6.38" x 3.60" x 1.10"(162.0 mm x 91.4 mm x 27.9 mm)
Housing dimensions
133 g (4.7 oz)
Weight
10-14 VDC at 100mA
Power requirement
Inovonics Wireless EchoStream
Radio
868-869 MHz
Operating frequency
0-60°C, (32-140°F) up to 90% relative humidity (non-condensing)
Operating environment
© 2005 Inovonics Wireless - www.inovonicswireless.com
® Serial Receiver
E B
D
C
Figure 1 Serial Receiver components
A. Housing release tab
C. Serial data terminal
E. Side cabling knockout
G. Receive LED
Warranty and Disclaimer
Inovonics Wireless Corporation ("Inovonics") warrants its products ("Product" or
"Products") to conform to its own specifications and to be free of defects in materials and
workmanship under normal use for a period of twenty-four (24) months from the date of
manufacture. Within the warranty period, Inovonics will repair or replace, at its option, all
or any part of the warranted Product. Inovonics will not be responsible for dismantling and/
or reinstallation charges. To exercise the warranty, the User ("User", "Installer" or
"Consumer") must work directly through their authorized distributor who will be given a
Return Material Authorization ("RMA") Number by Inovonics. Details of shipment will be
arranged directly through the authorized distributor.
This warranty is void in cases of improper installation, misuse, failure to follow installation
and operating instructions, alteration, accident or tampering, and repair by anyone other
than Inovonics.
This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express, or implied. There is no warranty by Inovonics
that Inovonics product will be merchantable or fit for any particular purpose, nor is there
any other warranty, expressed or implied, except as such is expressly set forth herein. In no
event shall Inovonics be liable for an incidental, consequential, indirect, special, or
exemplary damages, including but not limited to loss of profit, revenue or contract, loss of
use, cost of down time, or interruption of business, nor any claim made by distributor's
customers or any other person or entity.
This warranty will not be modified or extended. Inovonics does not authorize any person to
act on its behalf to modify or extend this warranty. This warranty will apply only to
Inovonics Products. Inovonics will not be liable for any direct, incidental or consequential
damage or loss whatsoever, caused by the malfunction of Product due to products,
accessories, or attachments of other manufacturers, including batteries, used in
conjunction with Inovonics Products.
A
F
G
GND Vs
RX TX
TAMPER
B. Serial data port
D. Bottom cabling knockout
F. Transmit LED
H. Decode LED
H