Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Vehicle Frame
Hitch Shown In
Proper Position
Equipment Required:
Fastener Kit: 75579F
Wrenches: 13mm, 15mm, 18mm
Drill Bits: None
Existing M12 Bolt
Existing M10 Bolt
1.
Lower exhaust by removing bolt which attaches rearmost hanger bracket to passenger's side frame rail. Retain bolt for
reinstallation.
2.
Remove existing bolts from frame rails as shown in Figure 2, (3) on driver's side, (2) on passenger's side and retain for hitch
installation.
3.
Remove plastic rivet holding plastic mud flap to Driver's side frame. May have to trim plastic after Step (4). You will not
reinstall plastic rivet.
4.
Raise hitch into position as shown in Figure 1 and attach with existing bolts removed in step 2. Hand tighten.
5.
Push hitch towards driver's side, so that passenger's side bracket is up against trunk pan, and tighten fasteners to
specifications below.
6.
Raise exhaust back into position and reinstall bolt removed in step 1.
Note: Rotating exhaust hanger bracket before tightening will add clearance between side bracket and exhaust.
Tighten all M10 CL10.9 fasteners with torque wrench to 53 Lb.-Ft. (72 N*M)
Tighten all M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007 Cequent Towing Products
Installation Instructions
Chrysler Town & Country
Dodge Grand Caravan
Fascia
Plastic mud flap in this
area. Remove plastic rivet
holding mud flap to frame.
Hitch must contact metal
frame. May have to trim
corner of plastic mud flap
after installing hitch.
Do not reinstall rivet.
Weldnuts
Figure 1
Figure 1
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Driver's Side
Frame Rail
Remove Bolt
Sheet 1 of 3
75579N
Part Numbers:
Max Gross
Trailer WT (LB)
5000 (2270 Kg.)
4000 (1816 Kg.)
Centerline of
Vehicle
Figure 2
Note: Uses all existing
Bolts on Vehicle
Existing M12 Bolt
Existing M10 Bolt
7-20-07
Form: F205 Rev A 5-6-05
75579
87451
44586
Max Tongue
WT (LB)
500 (227 Kg.)
400 (182 Kg.)
Passenger's
Side Frame
Rail
Remove
Bolt
Rev. A

Publicité

loading

Sommaire des Matières pour Cequent Towing Products 75579

  • Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2007 Cequent Towing Products Sheet 1 of 3 75579N 7-20-07 Rev.
  • Page 2 Ce produit est conforme aux dispositions et aux exigences de sécurité pour le raccordement des dispositifs et des systèmes de remorquage de l'État de New York, V.E.S.C. Règlement V-5 et SAE J684. Page 2 de 3 75579N 7-20-07 Rév. A 2007 Cequent Towing Products...
  • Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2007 Cequent Towing Products Hoja 3 de 3 75579N 7-20-07 Rev.

Ce manuel est également adapté pour:

8745144586