Télécharger Imprimer la page

Littelfuse FlexMod Harness Serie Mode D'installation

Publicité

Liens rapides

Installation Instructions
12805 Series Harness Kit for FlexMod Series
Part Numbers: 12805
Ordering Information
PART
NUMBER
12805
Deutsch-Type Connector & Harness Kit for FlexMod Series
This kit contains: 1 Dark grey connector shell, 1 Black wire & terminal assembly,
1 Blue wire & terminal assembly, 1 Red wire & terminal assembly, 1 White wire &
terminal assembly, 1 Violet wire & terminal assembly, 1 Orange wire & terminal
assembly, 5 Blank hole plugs, and 1 Green locking wedge
Installation
Assemble the 12805 Harness Kit in the following sequence:
1.
Look at the terminal location guidelines on the back of
this document. Select the appropriate one for the product
you are connecting to, and match the wire colors to the
locations (1-8).
2.
Identify the terminal location using the numbers on the
back of the connector. Terminals 1-4 are on one side, and
terminals 5-8 are on the other side.
3.
Find the right wire color for the terminal location you are
going to fill, and grip the connector body with one hand
with the back showing (see picture).
4.
With the other hand grip the wire assembly at the tail
end of the female pin, press the pin through the rubber
grommet. Continue pushing (the terminal will not be
visible) until you hear the pin click home.
5.
Pull on the wire. It should not back out at all.
6.
Repeat for all wires, then plug all empty terminal
locations with the blank hole plugs. (If you do not do this
step the connector is not sealed and it could allow water
to get into the connection and potentially damage the
electronic device.)
7 .
Make sure all the locking tabs are fully engaged (look for
any that are out of alignment). Then press the locking
wedge into the front of the connector until it snaps
home. Make sure the wings of the locking wedge
capture the seal and it is seated flush to the seal. If it will
not seat, check the locking tabs, as they will prevent the
lock from seating.
Steps 1-2
Pasos 1 y 2
Terminal
Numbering
Número del
terminal
Numéro de
borne
© 2020 Littelfuse Commercial Vehicle Products
littelfuse.com
DESCRIPTION
Étapes 1-2
Holes in Grommet
for Terminals
Agujeros en ojal
para terminales
Trous dans le passe-fil
pour les terminaux
Steps 3-5
Pasos 3 -5
Terminal Locations Guidelines
Pautas para las ubicaciones de los terminales
Guide d'emplacement des branchements
FOR PART NUMBERS: 48610 & 48710 - NÚMERO DE PARTE: 48610 & 48710
NUMÉRO DE PIÈCE: 48610 & 48710
NUMBER
WIRE COLOR
NÚMERO
COLOR DE CABLES
NUMÉRO
COULEUR DU FIL
1
Plug - Tapón - Bouchon
2
Black - Negro - Noir
3
Blue - Azul - Bleu
4
Red - Rojo - Rouge
5
Violet - Morado - Violet
6
White - Blanco - Blanc
7
Plug - Tapón - Bouchon
8
Plug - Tapón - Bouchon
FOR PART NUMBERS: 48541 & 487411 - NÚMERO DE PARTE:48541 & 48741
NUMÉRO DE PIÈCE: 48541 & 48741
NUMBER
WIRE COLOR
NÚMERO
COLOR DE CABLES
NUMÉRO
COULEUR DU FIL
1
Orange - Naranja - Orange
2
Black - Negro - Noir
3
Blue - Azul - Bleu
4
Red - Rojo - Rouge
5
Plug - Tapón - Bouchon
6
White - Blanco - Blanc
7
Plug - Tapón - Bouchon
8
Plug - Tapón - Bouchon
FOR PART NUMBERS: 48540 - NÚMERO DE PARTE:48540 - NUMÉRO DE PIÈCE: 48540
NUMBER
WIRE COLOR
NÚMERO
COLOR DE CABLES
NUMÉRO
COULEUR DU FIL
1
Orange - Naranja - Orange
2
Black - Negro - Noir
3
Blue - Azul - Bleu
4
Red - Rojo - Rouge
5
Violet - Morado - Violet
6
White - Blanco - Blanc
7
Plug - Tapón - Bouchon
8
Plug - Tapón - Bouchon
1 of 2
Étapes 3-5
CONNECTED TO
CONECTADOS A
POINT DE BRANCHEMENT
Not Used - No usado - Non utilisé
Required - Obligatorio - Obligatoire
Required - Obligatorio - Obligatoire
Required - Obligatorio - Obligatoire
Optional - Opcional - Optionnel
Optional - Opcional - Optionnel
Not Used - No usado - Non utilisé
Not Used - No usado - Non utilisé
CONNECTED TO
CONECTADOS A
POINT DE BRANCHEMENT
Required - Obligatorio - Obligatoire
Required - Obligatorio - Obligatoire
Required - Obligatorio - Obligatoire
Required - Obligatorio - Obligatoire
Not Used - No usado - Non utilisé
Optional - Opcional - Optionnel
Not Used - No usado - Non utilisé
Not Used - No usado - Non utilisé
CONNECTED TO
CONECTADOS A
POINT DE BRANCHEMENT
Required - Obligatorio - Obligatoire
Required - Obligatorio - Obligatoire
Required - Obligatorio - Obligatoire
Required - Obligatorio - Obligatoire
Optional - Opcional - Optionnel
Optional - Opcional - Optionnel
Not Used - No usado - Non utilisé
Not Used - No usado - Non utilisé
IF-164
Rev: 010320-F

Publicité

loading

Sommaire des Matières pour Littelfuse FlexMod Harness Serie

  • Page 1 Plug - Tapón - Bouchon Not Used - No usado - Non utilisé Plug - Tapón - Bouchon Not Used - No usado - Non utilisé 1 of 2 © 2020 Littelfuse Commercial Vehicle Products IF-164 Rev: 010320-F littelfuse.com...
  • Page 2 Imágenes de paso a paso en la Figura 1 de la página 1 peut empêcher la cale de blocage de reposer uniformément sur le joint. Procédure étape par étape en images à la figure 1, page 1 2 of 2 © 2020 Littelfuse Commercial Vehicle Products IF-164 Rev: 010320-F littelfuse.com...

Ce manuel est également adapté pour:

12805