Empire DVP20CC30-1 Instructions page 2

PARTS LIST - CONVERSION KIT 31052
Part Description
Pilot Orifice
Main Burner Orifice - DVP20CC
SIT Gas Valve Conversion Kit
Gas Conversion Label
Conversion Label
PARTS LIST - CONVERSION KIT 31058
Part Description
Pilot Orifice
Main Burner Orifice - DVP30CC
SIT Gas Valve Conversion Kit
Vent Flue Baffle - DVP30CC
Gas Conversion Label
Conversion Label
6-5/8"
BAFFLE
17-5/16"
BAFFLE
Page 2
Part Quantity
Number Supplied
R7658
P182 (#55)
R7657
R1321
R1322
Part Quantity
Number Supplied
R7658
P258 (#1.55)
R7657
30878 BL
R1321
R1322
Figure 1
Empire Comfort Systems Inc. • Belleville, IL
GAS INPUT FOR APPLIANCE CONVERTED TO PROPANE GAS:
DVP20CC30-1
DVP30CC30-1
1
The converted appliance when converted to Propane Gas will have a
1
manifold pressure approximately 10.0" w.c. (2.49 kPa) for maximum
input or 5.9" w.c. (1.469 kPa) for minimum input at the valve outlet
1
with the inlet pressure to the valve from a minimum of 11.0" w.c.
1
(2.739 kPa) for the purpose of input adjustment to a maximum of
1
13.0" w.c. (3.237 kPa).
INSTRUCTIONS FOR CONVERSION
1. If appliance is installed, turn off gas and electric supply to
appliance before making gas conversion.
2. Remove casting top from outer casting.
3. Remove casting front from outer casting.
1
4. Release two door latches at bottom of firebox.
1
5. Lift off glass frame from the bottom channel.
6. Carefully remove logs and set aside.
1
7. Remove the log shelf by removing the two screws securing the
1
log shelf to the rear wall.
1
8. Remove four 10 x 1/2" screws from burner base and one
8 x 1/4" screw from air shutter. Grasp burner assembly, lift and
1
pull forward to remove burner assembly.
9. Remove air shutter from orifice fitting.
10. Remove Natural Gas main burner orifice from orifice fitting.
11. Install Propane Gas main burner orifice into orifice fitting:
for DVP20CC ORIFICE MARKED 55
for DVP30CC ORIFICE MARKED 1.55 mm
12. Thread air shutter onto orifice fitting.
13. Pull upward on pilot hood to remove and gain access to pilot
injector orifice.
14. Remove Natural Gas pilot injector orifice from pilot burner
with 5/32" hex (Allen) wrench.
15. Insert appropriate Propane Gas pilot injector orifice into pilot
burner using the 5/32" hex wrench.
16. Re-install pilot hood to pilot assembly. Push downward to
snap in place.
17. Convert gas valve as instructed in the S.I.T. Gas Valve
Conversion kit.
18. Align burner assembly with air shutter as you place burner
assembly into original position in firebox.
19. Adjust air shutter setting to Full Open.
20. Attach air shutter to burner assembly with one 8 x 1/4" screw
from Step 7.
21. Attach burner assembly to firebox bottom with four 10 x 1/2"
screws from Step 7.
22. The converted fireplace must be connected to a supply of the
conversion gas and checked for leaks at all connections.
23. Remove flue vent baffle (17-5/16" wide). Install new flue vent
baffle (6-5/8" wide, DVP30CC only). See Figure 1.
24. Replace the log shelf and secure to the rear wall by replacing
the two screws removed in step 7.
25. Replace logs per instruction in Owner's Manual.
26. Place glass frame onto firebox and attach two door latches to
bottom of firebox.
27. The converted appliance must be connected to a supply of the
conversion gas and checked for leaks at all connections.
28. The appliance must be checked to ensure it is operating at the
correct pressure of 10.0" w.c.
29. Conversion is completed.
19,500 Btu per hour
26,500 Btu per hour
41331-1-0220