Publicité
Les langues disponibles
Les langues disponibles
Operating instructions
LED inspection light
Item no. 1439002
Intended Use
The product is intended to be used as a mobile light source. Through the practical pen form with clip, it can
be carried, for example in a shirt pocket, as a conventional pen. The product can be attached to a suitable
surface by the integrated magnet.
The operation of the product requires 3 batteries of the type AAA/micro (not included, can be ordered se-
parately).
For safety and approval reasons, you may not convert and/or alter the product. If you use the product for
purposes other than those described above, the product may be damaged. Furthermore, an improper use
involves risks such as short-circuits, fire etc. Please read the operating instructions carefully and do not dis-
card them. If you pass the product on to a third party, please hand over these operating instructions as well.
This product complies with the applicable National and European legal requirements. All names of compa-
nies and products are the trademarks of the respective owners. All rights reserved.
Package Contents
• LED inspection light
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code.
Follow the instructions on the website.
Explanation of Symbols
An exclamation mark in a triangle indicates important instructions in this operating manual which
absolutely have to be observed.
The arrow symbol is used when specific tips and information on handling sare provided.
Safety Instructions
Please read the operating instructions carefully and pay particular attention to the safety
instructions. We do not assume liability for injuries/material damages resulting from fail-
ure to observe the safety instructions and the information in these operating instructions
regarding the proper handling of the product. Furthermore, in such cases, the warranty/
guarantee will be null and void.
a) General
• The product is not a toy. Keep out of the reach of children and pets.
• Do not leave packing materials unattended. It may become a dangerous plaything for children.
• The product is designed for use indoors and outdoors. However, it must not be used in or
under water, as this will destroy it.
• Protect the product from extreme temperatures, direct sunlight, strong vibrations and combus-
tible gases, vapours and solvents.
• Never expose the product to mechanical stress.
• If safe operation is no longer possible, take the device out of service and secure it against
unintended use. Safe operation is no longer possible, if the product:
- has visible damage,
- no longer functions properly,
- has been stored under adverse ambient conditions for an extended period of time or
- has been exposed to considerable strain during transport.
• Please handle the product carefully. The product can be damaged if crushed, struck or drop-
ped, even from a low height.
• Attention, LED light:
Do not look directly into the LED light!
Do not look directly or with optical instruments into the light!
• If you have doubts about how the product should be operated or how to safely connect it,
consult a trained technician.
• Maintenance, adjustment and repair work may be carried out only by an expert or a specialist
workshop.
• If you have any questions, that are not answered in these operating instructions, please con-
tact our technical customer service or another specialist.
b) Batteries/rechargeable batteries
• Please observe the correct polarity when placing batteries/rechargeable batteries into the unit.
• If you are not going to use the device for a while, remove the batteries/rechargeable batteries
to prevent damage from leaking. Leaking or damaged batteries/rechargeable batteries can
cause acid burns upon contact with the skin. Thus, you should wear protective gloves when
handling damaged batteries/rechargeable batteries.
• Keep the batteries/rechargeable batteries out of the reach of children. Do not leave batteries
lying around, as they may be swallowed by children or pets.
• Replace all the batteries/rechargeable batteries at the same time. Mixing old and new batte-
ries/rechargeable batteries or mixing different batteries/rechargeable batteries in the device
may lead to battery leaks and will thus damage the device.
• Do not dismantle batteries/rechargeable batteries, do not short-circuit them and do not throw
them into fire. Never charge conventional, non-rechargeable batteries. There is a danger of
explosion!
Inserting Batteries, Replacing Batteries
• Open the battery compartment by twisting the cap slightly to the left in a counter-clockwise direction (note
label "OPEN" and the arrow) and then remove it.
• Insert three batteries of the type AAA/micro observing the right polarity (see the figure on the cap, the
positive pole of each of the three batteries must always point towards the battery compartment).
• Place the cap on (only one position is correct), and twist it gently in a clockwise direction to the right , so
that the flat side of the cap coincides with that of the LED inspection lamp.
• A battery chance is necessary when the brightness of the LED inspection lamp is considerably reduced.
Then change the batteries quickly, because the empty batteries can leak and damage the product, resul-
ting in loss of guarantee/warranty!
Please note:
It is possible to operate the LED inspection lamp with rechargeable batteries instead of bat-
teries. However, due to the lower capacity of the rechargeable batteries and a lower voltage
(rechargeable battery = 1.2 V, battery = 1.5 V), operating time is much shorter. In addition, the
rechargeable batteries are very sensitive to cold temperatures.
We therefore recommend to use only high-quality batteries for operating the LED inspection
lamp.
Operation
• Turn the LED inspection lamp on or off again by pressing the on/off switch "
• By means of the integrated magnet of the LED inspection lamp you can attach it to a suitable metal
surface.
• Through the clip on the side, the LED inspection lamp can be attached like any conventional pen to a shirt
pocket for example, or it can be attached to a flat surface.
• The LED inspection lamp can also stand on a level, flat surface by measn of the flat top of the cap.
Care and Cleaning
• Never use abrasive cleaning agents, cleaning alcohol or other chemical solutions, since these could da-
mage the enclosure or even impair operation.
• Use a dry, lint-free cloth to clean the product.
Disposal
a) Product
Electronic devices are recyclable material and do not belong in the household waste. Dispose of
the unserviceable product in accordance with the relevant statutory regulations.
Remove any inserted batteries/rechargeable batteries and dispose of them separately from the
product.
b) Batteries/rechargeable batteries
As the end user, you are required by law (Battery Ordinance) to return all spent batteries/rechargeable
batteries; disposal of them in the household waste is prohibited.
Batteries/rechargeable batteries contain harmful materials and are labelled with the symbol
shown to indicate that disposal in the household waste is forbidden. The symbols of the critical
heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead (the marking can be seen on the battery/
rechargeable battery, e.g. underneath the refuse bin symbol shown on the left).
You can return your used batteries/rechargeable batteries free of charge at the official collection points of
your community, in our stores, or at places where batteries or rechargeable batteries are sold.
You thereby fulfil your statutory obligations and contribute to the protection of the environment.
Technical Data
Operating voltage ........................4.5 V/DC (3 batteries of type AAA/micro)
Type of protection ........................IP64
LED bulbs ....................................8
The bulbs are in-built and can not be replaced.
Luminous flux ..............................180 lm
Light colour ..................................13,000 K (cold-white)
Operating/storage conditions ....... -20 °C to +45 °C, max. 93% relative humidity, non-condensing
Dimensions ..................................158 x 23 x 28 mm (L x W x H)
Weight .........................................35 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE.
" on the upper end.
1439002_V1_0616_02_VTP_m_en
Publicité
