Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75662F
Wrenches: 3/4" & 1-1/8"
Set the ¾" hex nut
into the cut out on
the strap, to assist
installation.
Qty.
j
Hex bolt 3/4-10 X 3.5 GR5
(1)
Qty.
k
Conical washer ¾"
(1)
Qty.
l
Hex nut 3/4-10
(1)
Qty.
m
Carriage bolt ½-13 GR8
(2)
1.
Removal of the spare tire can make installation easier, however, removal not necessary.
2.
Remove trailer ball cover cap in center of bumper.
3.
Install the conical washer and 3/4" hex bolt into the trailer hitch ball attachment hole in vehicle bumper.
4.
Raise hitch into position.
5.
Slide the 3/4" hex nut into position under rear attachment (hand tighten only until all fasteners are installed).
6.
Feed pull wire through cross member. Attach spacer (Item 5), attach to carriage bolt (Item 4), and pull fasteners through vehicle
cross tube and into position as shown.
7.
Loosely install conical washers (Item 6) and nuts (Item 7) onto carriage bolts.
8.
Torque all fasteners to specifications.
Tighten all ¾-10 GR5 fasteners with torque wrench to 260 Lb.-Ft. (353 N*M)
Tighten all ½-13 GR8 fasteners with torque wrench to 110 Lb.-Ft. (149 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body
panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety
precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.
Regulation V-5 and SAE J684.
`
2009 Cequent Performance Products
z
Installation Instructions
Step bumper required:
Hitch design for Step bumper.
q
l
Dodge Ram
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
j
k
l
Qty.
n
Spacer
(2)
Qty.
o
Conical washer ½"
(2)
Qty.
p
Hex nut ½-13
(2)
Qty.
q
Pull wire
(2)
.
Sheet 1 of 3
75662N
Part Numbers:
75662, 87530,
44603, 41895
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
10,000 (4540 Kg)
6000 (2724 Kg)
Feed pull wire
n
o p
m
Removal of the spare tire can make
installation easier, however,
removal not necessary.
10-26-09
Form: F205 Rev A 5-6-05
(U-Haul)
Max Tongue
WT (LB)
1000 (454 Kg)
600 (272 Kg)
Crossmember
Rev. E
Publicité
Manuels Connexes pour Cequent Performance Products 75662
Sommaire des Matières pour Cequent Performance Products 75662
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2009 Cequent Performance Products Sheet 1 of 3 75662N 10-26-09 Rev.
- Page 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2009 Cequent Performance Products Feuille 2 de 3 75662N 10-26-09 Rev.
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2009 Cequent Performance Products Hoja 3 de 3 75662N 10-26-09 Rev.